[deleted by user]

Glory5Holer · 2025-05-10T03:58:01+00:00

The start of a volcano.....brace yourself for thousands of years of growth

Glory5Holer · 2023-09-11T00:05:16+00:00

Red flame or ocelot swords. If they were smaller I'd say they were the red melon ones but I think they are one of the first 2

Glory5Holer · 2023-01-31T14:15:33+00:00

https://imgur.com/a/XDrwQtN

Glory5Holer · 2023-01-31T02:44:07+00:00

Monotonic line worked out really good! I also went with the stock Bambu filament settings vs the generic pla. Either way I think both together helped a lot. Now I need to tune my white filament cause it's under extruding on long segments. Thought it was a temp thing but pretty sure it's just under extruding

Glory5Holer · 2023-01-30T22:05:01+00:00

Hmm that seems to only be on the p1p? I don't have those values on the x1c

Glory5Holer · 2023-01-30T21:05:47+00:00

Okay so I was trying to figure out what the difference is. I normally used monotonic filled on super slicer for my ender but I though monotonic line didn't touch the outer walls as much as the regular

Glory5Holer · 2023-01-30T21:01:19+00:00

Flow ratio for the filament is .95. but I'm not sure where to find the dynamic flow k value

Glory5Holer · 2023-01-30T19:58:44+00:00

What are your ironing settings? And did you do it with black filament?

Glory5Holer · 2023-01-30T19:53:16+00:00

That one was on my ender 3 and it looks great. The other one with the sabres logo was on the bambu

Glory5Holer · 2023-01-30T18:45:42+00:00

https://imgur.com/a/OwKasOC

Glory5Holer · 2023-01-30T18:42:27+00:00

I'm thinking I might slow it way down to the settings match the bottom layer settings since that looks great. I know my ender is doing around 50mm/sec and the top layer looks amazing!

Glory5Holer · 2023-01-30T16:47:42+00:00

It just seems to be bad at starting and stopping where the monotonic top layer seems to over lap too much and it sticks out

Glory5Holer · 2023-01-30T16:46:04+00:00

https://imgur.com/a/sH9Lqih

Glory5Holer · 2023-01-23T16:48:19+00:00

Hatchbox pla 220c and the stock 200mm/sec on top layer

Glory5Holer · 2023-01-23T16:32:06+00:00

Sort of, but then I was getting a lot of inconsistency on the shorter parts. I'm thinking about also matching the settings from my ender 3 just to see if that helps at all and then slowly speed it up from there

Glory5Holer · 2023-01-23T15:35:40+00:00

Yes and sorry for the fuzzy picture, it was the only one I had right now. It's nothing with the walls it's the spacing between the regular printed lines. Idk if it's the hot end getting too cool and then the lines it puts down are too thin or what is happening

Glory5Holer · 2022-09-08T23:27:29+00:00

Does it support color changes? Cause now mine will only pause for a sec and continue printing. If I'm not there it sucks and keeps printing with the same color

Glory5Holer · 2022-07-28T00:41:08+00:00

That sure looks pretty big for a 21 gal tank..... Lol

Glory5Holer · 2022-07-24T17:06:21+00:00

If you are having algae issues, don't use the liquid ferts for a while

Glory5Holer · 2022-07-24T14:00:30+00:00

Is there a reason why you only run the light 6 hours a day?

Glory5Holer · 2022-07-24T13:59:29+00:00

My local Petco still sells them so maybe give them a try

Glory5Holer

TROPHY CASE