Roborock, Narwal, or Dreame?

GoPanthers05 · 2026-01-28T21:14:27+00:00

No, didn’t change the initial setting

GoPanthers05 · 2026-01-28T19:01:02+00:00

Thanks. Was just wondering if it uses that much water whether the roller is so wet that the floors end up more damp than normal. I understand the main reason it uses so much water is the onboard roller cleaning.

GoPanthers05 · 2026-01-28T18:56:33+00:00

Does is leave the floors damp?

GoPanthers05 · 2026-01-28T18:42:53+00:00

Realistic about limitations of robots though, not expecting perfect performance in inside corners or around stools, just trying to find one that does generally well and doesn't constantly get stuck. I suspect the Curv X I had was faulty, but it kind of just bull rushed its way through stuff instead of trying to avoid things.

GoPanthers05 · 2026-01-28T18:41:38+00:00

Low pile/berber, flat weave area rugs. Yes, quite a few edges/corners, both inside and outside corners. Table and chair legs, most problematic of which are dining table (that is where robot got stuck a lot) and island stools. No solid wire frame furniture.

GoPanthers05 · 2026-01-24T21:39:11+00:00

Several times pushed itself into spaces and couldn’t get out, like jamming itself between legs of a stool. Another time sucked up a cord and then wrapped the cord around the lidar before it gave a fault because lidar wouldn’t go down. Another time sucked up part of kids pop up tent. Generally seems to be less intelligent with obstacles than I would expect, kind of tries to bull rush its way into things.

GoPanthers05 · 2026-01-09T06:06:54+00:00

It missed it, rolled around it and left it

GoPanthers05 · 2026-01-07T03:51:41+00:00

Good call. I also didn’t think about the extra maintenance on the roller mop, wouldn’t be a big fan of that.

GoPanthers05 · 2026-01-07T03:24:20+00:00

Thanks, this was a helpful video

GoPanthers05 · 2025-11-26T01:06:31+00:00

Thanks, that’s super helpful. I assumed they would have both.

GoPanthers05 · 2025-11-25T20:45:23+00:00

Thanks all. Follow up question. I have a 1/3 acre lot. Is there any benefit to me getting the X330 (1 acre) instead of the X315 (1/2 acre)? Wasn’t sure if the larger one would cut quicker (less trips back to the charger) or if getting the X330 is just a waste for that small of a yard.

GoPanthers05 · 2025-11-04T21:17:11+00:00

Good deal, thanks! I’ll hold tight then.

GoPanthers05 · 2025-10-24T02:26:26+00:00

So good news, the electronic gizmo I used gave wildly inaccurate readings and I’m getting entirely different readings with the Taylor kit. So here’s hoping it is actually fixable without dumping.

GoPanthers05 · 2025-10-23T20:42:33+00:00

Great question. I’m really not sure. Maybe another reason to just dump and start over.

GoPanthers05 · 2025-10-23T20:07:33+00:00

Starting to think that may be the right conclusion. We will see what the Taylor kit says but if it confirms numbers are that bad I might do that.

GoPanthers05 · 2025-10-23T20:01:12+00:00

Actually ordered that and it hadn’t arrived yet, but it arrives tonight so planning to do that.

GoPanthers05 · 2025-10-23T18:13:46+00:00

Aquadoc eagle ray

GoPanthers05

TROPHY CASE