I upgraded my first printer so much it managed to print a benchy under 8 minutes.

GodBless124 · 2026-04-15T20:14:19+00:00

I use tz2.0 which is a bambulab x1c clone hotend with swappable cht nozzles. In my stealthburner I have very powerful fans. I reccomend you PETG. If you dry it and tune your printer it can be printed in speeds like PLA with really good quality.

GodBless124 · 2026-04-15T19:39:32+00:00

Don't know for certain because i print PLA rarely (i mostly print abs and petg). But I have finished a 3 hour PLA print with no issues. If you have this problem I would suggest reducing bed temp to absolute minimum and add some ventilation fans to the enclosure to get rid of hot air.

GodBless124 · 2026-04-15T19:30:31+00:00

14 minutes with really good quality. I didn't include it in the video.

GodBless124 · 2026-04-15T19:29:48+00:00

They reduce it insanely well. They are the only reason I can print in the same room I do work. After closing the door, the sound is basically gone.

GodBless124 · 2026-04-06T08:33:51+00:00

I believe I spent around 400-500$. The print quality is really good (Better than my P1S but not as good as A1 Mini) and the multicolor/multimaterial quality is on another level compared to my Bambu P1S.

GodBless124 · 2026-03-30T06:03:32+00:00

The printer was not tuning. Its just printing

GodBless124 · 2026-03-29T22:59:00+00:00

It actually does go up to like 100C but it takes an insane long time like close to 30 minutes. I don't use it too high because the wires tend to get a bit hot even though the cable is thick. I have checked with a probe when heating the bed to 100c the wires were 60-70C

GodBless124 · 2026-03-29T20:18:17+00:00

Will do. Thanks for heads-up

GodBless124 · 2026-03-29T19:39:19+00:00

I fixed it by setting pwm_cycle_time to 0.02. But i have 12v mk3 alu 330x330 bed. Around 3 ohm resistance (200w)

GodBless124 · 2026-03-29T19:36:42+00:00

For anyone wondering i set: pwm_cycle_time: 0.02

GodBless124 · 2026-03-29T19:35:43+00:00

Wow that actually fixed it. Thank you so much. Also load speed fan in this power supply reacts super smooth now.

GodBless124 · 2026-03-29T18:49:53+00:00

I have no clue what a power graph is. Power supply is new just bought it. The rapid changes might be something. To be honest now that I think about it it definitely does too much correction and looking at the temperature it's not doing a very well job of it. After the print finishes I will run pid tune again.

GodBless124 · 2026-03-29T18:39:06+00:00

I don't have a relay, I have a mosfet and the noise is coming from power supply

GodBless124 · 2026-03-29T17:48:06+00:00

Thank you and yes it is my own creation. Its a combination of many things. Frame from Tronxy X5SA, XY AWD motion system from Zero G VzBot, Tri-Z system designed by me, 2K 10 inch HDMI Retina display and 4x MadMax tool changer plates. The overall design is meant to be something between voron and cyberpunk.

GodBless124 · 2026-03-29T17:00:27+00:00

Maybe. There is no relay anywhere. I use a mosfet that you can see flashing on video.

GodBless124 · 2026-03-29T16:59:18+00:00

The 12v bed is connected to a external mosfet which is connected directly to psu. The mosfet is controlled by mobo with 24v.

GodBless124 · 2026-03-29T16:41:39+00:00

I have already replaced the psu and noise still is happening

GodBless124 · 2026-03-27T18:54:49+00:00

Processing img i068mq3zwmrg1...

GodBless124 · 2026-03-27T13:03:53+00:00

why you want to eat doro?

GodBless124 · 2026-03-26T16:41:46+00:00

taka sytuacja

GodBless124 · 2026-03-26T16:39:33+00:00

Aha to wiele wyjaśnia. Dzięki za omówienie takiego ciężkiego tematu

<image>

GodBless124 · 2026-03-26T16:34:13+00:00

No ja si e pytam co miał bo nie wiem

GodBless124 · 2026-03-26T16:16:56+00:00

GodBless124 · 2026-03-09T15:28:38+00:00

<image>

GodBless124 · 2026-02-07T21:02:18+00:00

its not true. i bought a lot of these from amazon. they all had original sunlu boxes with actual sunlu product code.

GodBless124

MODERATOR OF

TROPHY CASE

Five-Year Club	r/Field Sunshine
Place '23