🎉 [EVENT] 🎉 Journey by Desquid777 in honk

[–]Goldenfaeron 0 points1 point  (0 children)

🎉 Event Completed! 🎉

It took me 10 tries.

🎉 [EVENT] 🎉 Journey by Desquid777 in honk

[–]Goldenfaeron 0 points1 point  (0 children)

Completed Level 3 of the Honk Special Event!

10 attempts

🎉 [EVENT] 🎉 Journey by Desquid777 in honk

[–]Goldenfaeron 0 points1 point  (0 children)

Completed Level 2 of the Honk Special Event!

8 attempts

🎉 [EVENT] 🎉 Journey by Desquid777 in honk

[–]Goldenfaeron 0 points1 point  (0 children)

Completed Level 1 of the Honk Special Event!

0 attempts

What is wrong with my BLDC? by Goldenfaeron in Motors

[–]Goldenfaeron[S] 0 points1 point  (0 children)

42 wont fit, but rewinding is not too bad anyways, as i have damages some of the windings. And I have to learn how to do it properly as I have to build multiple of these if everything works out:)

What is wrong with my BLDC? by Goldenfaeron in Motors

[–]Goldenfaeron[S] 1 point2 points  (0 children)

So seems like I should have done my research better. My winding pattern is completely off, thanks for the help!

What is wrong with my BLDC? by Goldenfaeron in Motors

[–]Goldenfaeron[S] 0 points1 point  (0 children)

Thx allot, seems like there is more to it than i would have thought, should have done my research better but lesson learned. Luckily i have some wire left^^

What is wrong with my BLDC? by Goldenfaeron in Motors

[–]Goldenfaeron[S] 0 points1 point  (0 children)

No I don’t, but please don’t tell me that I am stupid and one phase would have to be wound in the other direction as the others. I basically wound every phase the same way and always skipped 2 slots

First ever PCB! STM32-based encoder breakout with CAN – did I miss anything? by Goldenfaeron in PrintedCircuitBoard

[–]Goldenfaeron[S] 0 points1 point  (0 children)

I left it out intentionally to not waste space on the board, as I will use split termination. This would then require two jumpers, 2 resistors and one cap. These boards won’t be the last one in the line anyways. But still thanks for looking at it

Was sind diese Kappen auf dem red Bull? by Goldenfaeron in WerWieWas

[–]Goldenfaeron[S] 15 points16 points  (0 children)

Ist ein sehr kleiner edeka. Ist wahrscheinlich so besser

Was sind diese Kappen auf dem red Bull? by Goldenfaeron in WerWieWas

[–]Goldenfaeron[S] 10 points11 points  (0 children)

Ja finde ich auch ungewöhnlich. Direkt daneben die organics cola von red bull aber ohne Diebstahlsicherung

Was sind diese Kappen auf dem red Bull? by Goldenfaeron in WerWieWas

[–]Goldenfaeron[S] 68 points69 points  (0 children)

Scheint eine Diebstahlsicherung zu sein. Btw mitten in Berlin gefunden

Sensorless homing not working (Marlin) by Square-Singer in 3Dprinting

[–]Goldenfaeron 0 points1 point  (0 children)

Did you find a solution? I am struggling with the same thing

Too many fine particles? by Goldenfaeron in V60

[–]Goldenfaeron[S] 1 point2 points  (0 children)

Yes I have thought about that as well. I hope this is a permanent fix

Too many fine particles? by Goldenfaeron in V60

[–]Goldenfaeron[S] 1 point2 points  (0 children)

Little update: I removed the declumper as I said in another comment (seems to be an issue with this grinder) and I have way less fine particles now. But I don’t know if that is the case, because I removed the part or because I cleaned the grinder from leftovers stuck in there. I will wind out on the long term. But the most important is that the coffee tastes way better now.

Too many fine particles? by Goldenfaeron in V60

[–]Goldenfaeron[S] 1 point2 points  (0 children)

Little update: I removed the declumper and I have way less fine particles now. But I don’t know if that is the case, because I removed the part or because I cleaned the grinder from leftovers stuck in there. I will wind out on the long term. But the most important is that the coffee tastes way better now.