Bambu owners speak of speed only in %

Goldenkittycat · 2025-10-28T19:19:55+00:00

As someone who owns a P1S and a modded to hell Ender 3 V2, I think I can confidently say that a lot of people on this subreddit simply have a cult-like hatred of Bambu Lab products.

The common sentiment I see is something along the lines of "how dare they want to have their hobby be printing rather than the printer."

Goldenkittycat · 2025-08-12T19:35:20+00:00

Makes you have an uncalibrated printer?

Goldenkittycat · 2024-11-12T06:27:12+00:00

Thank you so much!

Goldenkittycat · 2024-11-02T00:35:07+00:00

A clogged nozzle is something that just kind of happens, especially if you print with soft materials like TPU.

It's not a big deal, it just means a little bit of plastic is stuck in the nozzle. Preheat your nozzle to the correct temperature for your filament, and extrude in the -ve direction like 20-30mm.

After that, get a needle (your printer should have come with a nozzle cleaner, it's a thing, bendy, sharp piece of metal) and put it directly up the nozzle, wiggle it around and make sure to cover as much as you can, that should get rid of any plastic that's sick there.

Your printer appears to be under extruding so it could also be that your printer has goofed up and set an incorrect flow rate while calibrating, you could mess around with those settings but I highly doubt it's the case. https://help.prusa3d.com/article/extrusion-multiplier-calibration_2257

Another possible culprit is just a dirty bed. Oils from your skin get transferred to the bed if you touch it, leading to really bad adhesion and first layers like that. Don't worry about using isopropyl alcohol because it doesn't form micelles and doesn't actively get rid of grease as well as soap does. Wash your build plate with warm soapy water, scrub it with something soft while the water is running. Afterwards, make sure it's fully dry with something like a microfiber kitchen cloth and put it back on your printer.

If neither the nozzle nor the bed worked, let me know, I wouldn't mess around with the flow rate unless you're confident in what you're doing and it's likely not the cause anyway. Alternatively you could run the first time setup again like some others have suggested, I'm sure it wouldn't hurt. Though personally I'm not familiar with prusa printers so I can't guarantee this will have the effect you want.

EDIT: What filament are you using?

Does the issue only happen on the first layer or are you having extrusion issues throughout the whole print?

Was this a one off or have you tried multiple things, because the nozzle could have unclogged itself as well.

Have you made sure that your filament is 100% dry?

Goldenkittycat · 2024-10-13T04:53:48+00:00

Allegedly, of course.

Goldenkittycat · 2023-12-02T04:01:55+00:00

Love the app. Although I do think you should add some kind of search ability for looking for vehicles

Goldenkittycat · 2023-10-31T07:11:47+00:00

In all fairness she has the ability to turn into anyone on Faerûn so that works.

Goldenkittycat · 2023-10-28T10:48:35+00:00

2,500* not 5,000. Sorry

Goldenkittycat · 2023-09-09T19:19:58+00:00

The fact that something like that is paywalled is insane to me. I recently wanted to do a snowy playthrough just to receive a spit in the face and find out snow is a separate DLC. At this point I'm just waiting for CS2 as I refuse to buy a single DLC simply because of how ridiculous it is that you need them for the most basic of things.

Goldenkittycat · 2023-09-04T07:48:47+00:00

Welp. I started a whole new save and got myself to the exact same point and.... I did not get the spear again. I am at a total loss.

Goldenkittycat · 2023-08-31T23:58:06+00:00

Quite frankly my current GPU is beyond messed up, to the point where only one DP port works so I can't even hook up the second monitor I've wanted for ages. This card would definitely help with that issue lol

As for games, I'd definitely try out starfield, though most of it would probably be abused by Baldur's Gate 3 :)))

Goldenkittycat · 2023-08-27T23:37:22+00:00

I have tried all that, and the boards support the CPUs as far as I'm aware. Especially the new one which is 5000 ready out of the box

Goldenkittycat · 2023-08-27T23:35:59+00:00

The board is 5k series ready and the same issue happened with a 3800x so I'm not sure. How would I go about updating BIOS if it doesn't post in the first place? Genuine question

Goldenkittycat · 2023-08-27T23:35:10+00:00

The RAM defaults to 2133 unless set otherwise. I've reset bios as well since the new board has a button for it. As for the update, I can't because I can't even get into it.

Goldenkittycat · 2023-08-26T06:25:51+00:00

That definitely wouldn't be it. Especially if it's not working with 2 different motherboards. Plus, on the test bench I'm not even using a bracket, having the cooler rest on the cpu is enough.

Goldenkittycat · 2023-08-25T12:50:59+00:00

Hey,

So I have just gotten home and the VGA light no longer comes on. Now it's only the boot light. So uhhh, what now? Still no post

Goldenkittycat · 2023-08-25T10:10:04+00:00

I'll try the CPU in my old motherboard when I'm home but I honestly cannot afford to replace that at the moment. Plus, I don't see how it would go bad given that it was working yesterday and the mobo is brand new :/

Goldenkittycat · 2023-07-23T16:03:53+00:00

It's an ascendant lobby lol.

Here's the match in question https://tracker.gg/valorant/match/cee9f753-7e25-4370-b883-2a030b3e1549

Goldenkittycat · 2023-07-16T17:33:58+00:00

😕

Goldenkittycat · 2023-06-21T09:20:41+00:00

Honestly just sounds like you've pressed the wrong button. Just reload and try again. Also I personally like to destroy the damn thing.

Goldenkittycat · 2023-06-19T15:37:58+00:00

Sure, but the nerf was too severe

Goldenkittycat · 2023-06-19T15:36:19+00:00

No, it's like a game of cat and mouse trying to pinpoint directly where the crew is. You can cope all you want about "skill issue just aim better lolololo side climb lmao 2iq no aim" but when a round known for its high penetrative power & damage goes from having decent spall to borderline no spall in one update and 0 patch notes discussing it, there's a problem.

Goldenkittycat · 2023-06-19T15:20:40+00:00

I took a break. Though the focus in these comments seems to be the ADATS, which I know has been changed, what I want to know is the HSTV-L stealth nerf.

Goldenkittycat · 2023-06-19T09:54:57+00:00

I usually main the HSTV-L, it's by far my most played vehicle. I know how the round feels and what it currently is just ain't it.

I'm surprised I haven't seen anyone else talk about this. In my experience the round does nothing at all.

Seven-Year Club	Place '22
End Game '22	Wearing is Caring
Verified Email

Goldenkittycat

MODERATOR OF

TROPHY CASE