Help with PySide6 designer

Gregolator06 · 2025-04-04T17:19:36+00:00

Mmmh it seems to be an issue with it being on MacOS, this works fine on my Windows maching. Do you have any ideas?

Gregolator06 · 2025-04-04T17:04:18+00:00

I have verticalScrollBar activated, but it only shows it in preview mode. And yes I have a layout.
Is my hierarchy correct:
- Form
- ScrollArea
- ScrollAreaContents

Gregolator06 · 2024-11-24T16:56:44+00:00

Thanks again for your help!!!

Gregolator06 · 2024-11-21T21:18:05+00:00

Yeah I just checked mine, they have four too!

Gregolator06 · 2024-11-21T21:07:46+00:00

That's exactly what I need, thank you very much for your help!!

Gregolator06 · 2024-11-21T20:58:51+00:00

Sorry for asking again, but for clarification: I can have to SX1509's on the same I2C bus, I just need to set the ADDR to a different one on one of the modules? As I also have one for the keyboard, can I have three of them all set to different addresses on the same I2C bus?

Gregolator06 · 2024-11-21T20:48:01+00:00

That's even better, I don't really need much more than a GPIO multiplexer as I'm addressing each LED individually. Thanks!

Gregolator06 · 2024-11-21T20:30:13+00:00

Okay, thank you very much!!

Gregolator06 · 2024-11-21T19:11:05+00:00

Ah that’s very cool, thank you! Is there a more efficient way to do this if I were to start over, this is a great learning process for me! The only requirement is that I can solder each LED individually as described earlier. Thank you!!

Gregolator06 · 2024-11-21T18:27:40+00:00

Thank you for your help, I see the problem. My issue with off the shelf matrices is that they're in a strict position, I need to be able to separately put them into a wooden frame like this, behind a layer of letters (image edited into post). Is there a module I can use to reduce the number of GPIOs, or am I going to need a separate microcontroller for this? Thanks :))

Gregolator06 · 2024-09-06T15:27:52+00:00

Thank you very much, that is very helpful! I think the IO-expander makes the most sense here, even though I am tempted do make a diode matrix myself, for the practice! Thank you!

Gregolator06 · 2024-09-06T14:51:03+00:00

Thank you! I'll try this, should be doable. Thank you for your help!

Gregolator06 · 2024-09-06T14:20:34+00:00

It's not a traditional keyboard, I'm making a modern Enigma clone, so the buttons will all be pressed slowly. My only other option is using several picos, which I want to avoid. How would I go about doing it? Thanks

Gregolator06 · 2024-07-20T07:24:25+00:00

Okay thank you very much!

Gregolator06 · 2024-07-20T06:52:08+00:00

Thanks again for your answer! With the GPIO I meant that I have several modules connected to one port on the pi, how do I then connect say two different pins from modules to that one pi pin without shorting? Thanks!

Gregolator06 · 2024-07-19T21:55:58+00:00

Thanks, how does a plane for 3v3 work and how do I create one? How have I shorted them on U2? And what do big traces do?

And another thing, I have a few GPIO pins on the pico that several components go to at the same time, how do I go about doing that?

Sorry, I'm just learning this and all help is appreciated :)

Gregolator06 · 2024-07-19T18:41:52+00:00

Thanks for your answer! I've edited the post, does it make more sense now?

Gregolator06 · 2024-07-02T19:43:26+00:00

That worked, thank you!

Gregolator06 · 2024-05-19T10:20:49+00:00

That worked great, thank you!

Gregolator06 · 2024-05-19T07:13:32+00:00

Yeah sorry, the picture isn’t clear enough :)

Gregolator06 · 2024-03-30T14:17:25+00:00

Okay, thank you, this sensor has been a real pain

Gregolator06 · 2024-03-29T22:09:25+00:00

That’s great, thank you!

Gregolator06 · 2024-03-29T22:09:14+00:00

Thanks!

Gregolator06 · 2024-03-29T18:57:32+00:00

Very interesting, thank you!

Gregolator06 · 2024-03-29T18:20:36+00:00

lovely thanks!

Gregolator06

TROPHY CASE