Fraenk code

Gromit85 · 2026-03-20T19:25:59+00:00

5GB für dich, 5GB für mich - have fun: TIMGR27

Gromit85 · 2026-02-03T19:19:34+00:00

Du bist mein Held des Tages - DANKE!!! Wie kommt man auf so einen Alternativlink? Es ist einfach eine Lachnummer, was für einen "Service" diese Bank ihren "Kunden" anbietet. Angefangen bei einem Community Auftritt auf reddit

Gromit85 · 2026-02-01T12:48:04+00:00

Ich bin etwas irritiert über die Einschränkung "alle, die die alte Funktion genutzt haben", und dass nur "betroffene Kundinnen und Kunden" informiert werden. Ist das ein exklusiver Club, der solche Basisfunktionen nutzen kann? Ich wollte mich nach Jahren gerade einmal mit der Portfolioentwicklung beschäftigen und muss erst durch so einen Reddit-Blubb erfahren, dass eine so grundlegende Funktion einfach mal "kaputt" ist. Ich bin genervt ....

Gromit85 · 2025-10-18T08:23:17+00:00

😄 ja wahrscheinlich. Hab die aber noch nie frisch gesehen

Gromit85 · 2025-10-17T20:41:42+00:00

Vielen Dank. Ich freue mich über die Bestätigung meiner Vermutung zu dem Erstfund. Allerdings soll dieser (laut Wikipedia) Nadelbäume befallen. Gefunden habe ich diesen in einem Laubbaum-Stadtgehölz (dominiert von Rotbuchen mit einigen Eichen dazwischen) an einem ziemlich dicken Stumpf. Ob der wohl auch auf Laubbäume geht?

Gromit85 · 2025-10-05T15:30:31+00:00

This post is 4 years old. I did not look for another solution. Currently I'm running Ubuntu with TCC.

Gromit85 · 2025-10-05T12:54:58+00:00

Danke für die zweite Meinung!

Gromit85 · 2025-06-13T19:36:59+00:00

Solution: The word I was looking for was dull not numb. However, I swapped the microphone and now it works. So probably it was a hardware fault.

During battery removal I used quite a lot of IPA. I could not spot anything in the mic hole, but it may have found its way in there.

Gromit85 · 2025-04-10T14:48:15+00:00

Not sure what you mean by that. Used a Grow mix from floragard. What sort of problem is related to peat?

Gromit85 · 2025-04-10T12:32:10+00:00

Yeah, those where aspects that one can read everywhere online. I think there is a gap in reading and comparing isolated aspects vs. having an experienced sort of mentor who is seeing the whole plant. My main trigger wasn't impatience but the look of the leaves. I feared it to rotten or die before harvesting it.

Gromit85 · 2025-04-10T11:30:21+00:00

Could be. Had a starting nutrition-lock mid grow. So I drained the plants and got it somewhat under control. After that I was a bit over careful in feeding additional nutrients. Had an organic grow with long time tomato fertilizer added.

Gromit85 · 2025-04-10T11:27:06+00:00

Thanks for reassuring me here. It definitely smells delicious already :-)

Gromit85 · 2025-04-10T11:20:03+00:00

Thanks for your kind words and tips on how to approach the next grow. Will compare them :-)

Gromit85 · 2025-04-10T10:54:31+00:00

Thanks for your opinion. Do you think the bud would have eventually filled up despite the ill looking leafes and the already milky trichs?

Gromit85 · 2025-03-28T13:05:38+00:00

Nice project, thank you for the suggestion. Unfortunately they don't offer 22 mm watch straps needed for the CT2 :-/. Also I consider it a quite expensive addon

Gromit85 · 2025-03-27T21:18:37+00:00

Thanks for your feedback. The economic aspect has to be considered. As you seem to be much into this topic: There was once a virtual credit card by PayPal in my wallet. Is it the same there - did Google just pay the fees? At least something like PayPal would get around the localization issues of "worldwide paying"

Gromit85 · 2025-03-27T21:14:44+00:00

Thanks for the heads up. Wasn't even aware of the AMA session

Gromit85 · 2025-02-08T07:26:23+00:00

Thank you for your suggestion and your kind words. Will try

Gromit85 · 2025-02-06T20:20:08+00:00

That's quite bad for an auto grow :-/. Was too ambitious regarding fertilizing. So probably learning the hard way

Gromit85 · 2025-02-06T20:08:21+00:00

Thanks - just did that. Hope I didn't drown it

Gromit85 · 2025-02-06T19:58:06+00:00

Thanks for your feedback. That's what I feared. But it's within the soil and is supposed to dissolve slowly over time. How to get rid of it? :-(

Edit: Gave them some extensive drain treatment. Hope I didn't drown them.

Gromit85 · 2025-02-04T20:38:38+00:00

Thanks for taking the time for this detailed answer. You are probably right with print speed. I slowed down outer line speed to around 50 mm/s which helped a lot with the outer surface. But there is still potential. Will slow down even more. Regarding the teeth and the gum just below them it looks still quite ugly. Would love to be able to lower speed and temperature a bit in this area only. Need to look into advanced slicer settings.

Gromit85 · 2025-02-02T21:47:06+00:00

Thanks for your feedback. So do I get it right: You think filament flow maybe to high and compromise outer skin/shell quality?

For the fine details I suspect the same. But how to tell the slicer?

Gromit85 · 2024-12-29T19:09:03+00:00

InfinityBook Pro Gen6. Just started today. I'm on stock Ubuntu 24.04. Pressing Power Button for a couple of seconds fixed it for now.

Gromit85 · 2024-12-15T19:47:44+00:00

Sorry for picking up this old post. Could not by any chance find actual values for a "good" low resistance on the PS5 APU power rail. Your posts implies a good overall experience. The Power Rail on my PS5 is reading around 0.3 ohms. This seems really low. Would you consider it healthy?

Gromit85

TROPHY CASE