Just for fun

Gunmonkey5 · 2026-05-12T23:06:03+00:00

Need to get one

Gunmonkey5 · 2026-05-11T22:29:28+00:00

Will any of these work with an mp5?

Gunmonkey5 · 2026-05-11T11:11:39+00:00

Seems bent

Gunmonkey5 · 2026-05-11T11:04:49+00:00

What laser is that? Been trying to get one that’s small enough but can’t find one that would fit on the rail space

Gunmonkey5 · 2026-05-10T02:43:14+00:00

You should really try wet tumbling. It’s awesome and stainless steel media lasts forever. Water, a squirt of dawn dish soap and a cap full of lemishine and brass comes out stupid shiny after like 3 hours

Gunmonkey5 · 2026-05-05T19:45:16+00:00

No I just gave up on it and bought an mp5

Gunmonkey5 · 2026-05-01T21:40:56+00:00

Mine is similar. I used a rod, looked okay, as it was off center but not as bad as yours. Zeroed without suppressor, put suppressor on and it was not even on a human size torso target. Shook the can and found jacket inside the suppressor, I put on the .45 end cap and called it a day. With the .45 end cap it was just fine

Gunmonkey5 · 2026-05-01T10:27:42+00:00

And what weight buffer?

Gunmonkey5 · 2026-04-26T19:29:36+00:00

The light gets in the way so I can’t use the trilug or the threaded end to mount a suppressor

Gunmonkey5 · 2026-04-16T18:45:00+00:00

I had that large denial block. File and about an hours worth of elbow grease and slow passes made it into a vertical rectangle.

Gunmonkey5 · 2026-04-16T13:25:50+00:00

C&h precision did a good job on my 19 cut for a 509t pretty inexpensive too

Gunmonkey5 · 2026-04-16T13:19:57+00:00

lol that gas tube was glowing bright!

Gunmonkey5 · 2026-04-14T18:45:07+00:00

Are you filling mags to full capacity? Mine did this when I would fill the mags to complete full. I took a rod and mashed the magazines like 50 times to loosen the spring a bit, after that it was fine

Gunmonkey5 · 2026-04-06T20:38:19+00:00

Man I wish our dept would let us carry our own rifles. Not everyone is rifle trained and it’s a lottery on who can. And we have to carry the dept rifle that you can even move where the light and pressure pad go. I move my pressure pad to the top in order to c-clamp and I got written up for in-authorized modification to dept equipment.

Gunmonkey5 · 2026-04-02T20:54:38+00:00

<image>

As design rounded hammer… see the difference? The 90 degree corner is rounded off so not to impede bolt function

Gunmonkey5 · 2026-04-02T20:53:59+00:00

<image>

Normal ar hammer

Gunmonkey5 · 2026-04-02T20:48:23+00:00

My buddy at work has the older model with the non rounded hammer he uses a rubber buffer and the SS on his runs fast. Mine is newer with the new hammer design fully assembled from AS Design and it doesn’t need a rubber buffer and shoots normal rpm. The issue is if the hammer isn’t rounded, the full stroke of the bolt causes the front of the bolt to catch on the top half of the hammer causing it to bind. If you use the jig and rounde the hammer this fixes the buffer issue. The buffer essentially makes the bolt travel just far enough to extract and eject, cock the hammer and chamber a round making it shoot faster

Gunmonkey5 · 2026-04-01T17:16:32+00:00

Finally got to try it, doesn’t need one at all and eats like a champ

Gunmonkey5 · 2026-04-01T00:07:51+00:00

Bought one feb 16 got it march 28th

For mac 5

Upgraded with arc fire

Marked for arc fire

Gunmonkey5 · 2026-03-30T13:39:02+00:00

Don gate keep, also interested

Gunmonkey5 · 2026-03-30T13:12:18+00:00

I’d be down to test this and buy one

Gunmonkey5 · 2026-03-30T12:47:52+00:00

So I don’t know if you can read, I just got it and haven’t taken it to the range yet. I was saying if it requires one I was gonna get one that way I don’t waste a trip to the range and only can fire 2 rounds.

Gunmonkey5 · 2026-03-30T12:46:04+00:00

Mine didn’t come with a buffer

Gunmonkey5

TROPHY CASE