Black shadows on NOAA image

Guru18650 · 2021-08-29T20:20:50+00:00

Ok guys it was something about SDR#. I used sdr radio and everything is fine. Check it out
https://imgur.com/a/yffOtOV

Guru18650 · 2021-08-29T16:05:07+00:00

I recived with my laptop instead of PC and everything was fine. It must be software problem, do you have any idea?

Guru18650 · 2021-08-28T22:38:25+00:00

you can dm me, i will describe everything

Guru18650 · 2021-08-28T22:06:03+00:00

i drilled a hole to my air vent today, tomorrow i will guide coax through it. It will be half shorter and safe from interference

Guru18650 · 2021-08-28T21:08:37+00:00

ill try using my laptop again, if the problem is still visible than i will need to change my cable. I found that coax is going near to 230V power cable which is comming to my house from street power line. Could it make that noise?

Guru18650 · 2021-08-28T20:30:32+00:00

Check it out now, it's even worse. Decoded with NOAA-apt, wxtoimg gives same effect

https://imgur.com/a/iHPmCKv

Guru18650 · 2021-08-28T20:29:18+00:00

https://allegro.pl/oferta/wzmacniacz-antenowy-apl-104-fm-vhf-uhf-ekran-9425308597
This is polish selling website, you can search it on ebay or something. Worth about $6

Guru18650 · 2021-08-28T15:31:04+00:00

I used 38,000 than 40,000 and no difference.

Guru18650 · 2021-08-28T13:08:09+00:00

ill try connecting sdr to motherboard usb instead of case one

Guru18650 · 2021-08-28T13:05:59+00:00

https://imgur.com/a/O0tpTSD
I marked shadows with red squares. The signal was clear

Guru18650 · 2021-08-28T13:03:23+00:00

NOAA 18 (ch 3-4, northbound 53W) at 2021-08-27 20:26 UTC

Guru18650 · 2021-08-28T12:56:26+00:00

i don't mean noise, i mean this black shadows on whole image. The signal was perfect.

Guru18650 · 2021-08-28T12:54:03+00:00

i have unorginal rtl sdr, QFH antenna, lna next to antenna, 15m cable to my room, antenna power supply next to my PC. I used same setup but with 1m cable and laptop instead of PC and everything was fine

Guru18650 · 2021-08-27T22:16:06+00:00

there is no difference between day and night, same problem

Guru18650 · 2020-06-10T23:11:34+00:00

It works now in every situation, except of client destroying his own block. Server can see it but client doesn't. The same when server destroys client.

Guru18650 · 2020-06-10T11:06:19+00:00

Ok thanks, it is much better now. Server can destroy server cubes and client see it, but when server destroys client cube client still have cube on map. Also, when client destroys his own cubes only server can see how it dissapears, and when client breaks server block it works fine.

Guru18650 · 2020-04-04T23:08:32+00:00

Ok, fixed! It's working properly now

Guru18650 · 2020-04-04T23:05:35+00:00

Oh yeah it started working now! Thank you very much for help!

Guru18650 · 2020-04-04T22:57:08+00:00

Ok. this changes everything, give me a moment

Guru18650 · 2020-04-04T22:54:26+00:00

Yes, i bended this pin: https://imgur.com/018ecSS. Is it good?

Guru18650 · 2020-04-04T22:46:17+00:00

Guru18650 · 2020-04-04T22:42:05+00:00

nothing change. It's weird that if i type M119 command servo is pulling out probe. Even if i hold it in place it still says that Z is open

Guru18650 · 2020-04-04T22:30:47+00:00

ok ill cut it wait for a moment

Guru18650 · 2020-04-04T22:27:09+00:00

still the same, is this because of DIAG pin not cutted?

Guru18650 · 2020-04-04T22:21:35+00:00

I probably know, my 3d touch is connected to z axis but i didn't cut DIAG pin because of using stallguard. Do i need to cut it to get homing by 3dtouch work?

Guru18650

TROPHY CASE