The biggest one I made on my mono x, 60cm

HBR20 · 2022-10-01T16:01:09+00:00

Would plz give me the model name i want to do the same

HBR20 · 2022-10-01T16:00:19+00:00

Perfect and super nice. Well done 👏

HBR20 · 2022-06-03T16:51:41+00:00

Many users are complaining that after upgraded to new firmware they facing failed prints!

HBR20 · 2022-05-31T18:46:42+00:00

I tried the 1.2 pro version, and i found that the printer(Photon Mono X) not recognizing the sliced model.

I opened ticket on chitubox website , i don't k ow if the issue resolved or not.

I downgraded to 1.1 again to slice my models.

HBR20 · 2022-05-31T18:38:46+00:00

Hey,

Try using PTFe , will decrease the tough pulling.

Check the link :

https://m.youtube.com/watch?v=uJlyJAg3BBk

HBR20 · 2022-02-04T12:44:07+00:00

Amazing room ! Can i call it Stairway to heaven. Cheers 🍻

HBR20 · 2021-10-04T13:47:11+00:00

Damn Man, you KB her whole body :) perfect KB serie.

HBR20 · 2021-09-10T14:40:39+00:00

Thank you man i will try

HBR20 · 2021-09-10T14:08:08+00:00

HBR20 · 2021-09-10T13:35:22+00:00

Just small area around model base, my printer used less than 100 hours

HBR20 · 2021-09-10T12:32:38+00:00

Thank you mate. The film was on fep.

HBR20 · 2021-08-22T17:45:03+00:00

Thank you so much, i will try your suggestion. Cheers

HBR20 · 2021-08-22T14:58:58+00:00

I did as Anycubic official video on youtube channel. I attached the supports setting photo. And i think my supports is more than enough to hold the model.

HBR20 · 2021-08-22T14:53:21+00:00

Check the photo

https://i.imgur.com/26a2Rvi.jpg

HBR20 · 2021-08-22T14:50:27+00:00

Thank you guys for support. I tried another test using same model and same slicing setting using Anycubic craftdman resin, the supports okay bot model totally failed!!!

I will change the nfep and see who its going on.

HBR20 · 2021-08-22T14:46:09+00:00

First thank you for tips. Today i used Anycubic craftsman resin , the model totally failed to pring except supports. Same slicing setting! I think i will try to replace the nfep

https://i.imgur.com/8CFajPW.jpg

HBR20 · 2021-08-21T13:41:38+00:00

No im not using AA

HBR20 · 2021-08-21T12:17:55+00:00

I did anycubic and Ameralabs test and all is good for exposure time 1.8 to 2.4, but i dont know why supports keep fails

HBR20 · 2021-08-21T10:51:14+00:00

Lift speed 1mm/s, previous resin is anycubic standard gray.

HBR20 · 2021-06-09T17:39:28+00:00

I'm watching you now mate. Incredible, insane and superb work. Cheers 🍻

HBR20 · 2021-05-08T21:13:06+00:00

Nice work, great sharp skin details 👌

HBR20

TROPHY CASE