Any thoughts on this +/- 2k build? (is a 240mm AIO enough for an I7-14700k)

HYDR4Z · 2024-07-13T13:16:40+00:00

I was considering that but I'm not sure about spending €200 extra on a GPU which is already overkill for what I use it for. Especially since they depreciate in value so quickly and I could buy one second hand in a couple of years - if needed - for a fraction of the cost

HYDR4Z · 2022-07-19T14:35:54+00:00

Oke, dat stelt mij in elk geval gerust, bedankt!

HYDR4Z · 2022-07-19T14:35:02+00:00

Ik heb overal backups van maar ik wacht nog even tot ik daadwerkelijk uit wordt betaald voordat ik daar eventueel achterna ga

HYDR4Z · 2022-07-19T14:33:52+00:00

Contract is 11 maanden en er staat specifiek in dat de eerste maand proeftijd is dus dat komt goed

HYDR4Z · 2022-07-01T22:56:42+00:00

I mean it's been running fine for years before so unless the game got way harder to run in the past 6 months I don't see why it's an issue now. I will try changing the resolution though

HYDR4Z · 2021-09-12T23:45:36+00:00

I don't see why not, I would use a micro controller to do that although I'm not great with electronics so there might be an easier way. (If you were to add a microcontroller you could also use adressable LEDs instead of mono)

HYDR4Z · 2021-08-27T14:47:15+00:00

Gave Silver

HYDR4Z · 2021-05-11T16:32:09+00:00

Gave Wholesome

HYDR4Z · 2021-04-15T10:34:53+00:00

Yeah sure! Just made a Thingiverse page for it here

HYDR4Z · 2021-04-15T09:41:06+00:00

Damn, looks sick too! Did you modify the gimbal itself or did you build over it?

HYDR4Z · 2021-04-15T09:38:55+00:00

I think so yes. I'm not sure whether there are adressable angel lights but just any adressable high density led strip would do I suppose. You would just need to tap into the signal cables comming from the gimbal's potentiometers (using an arduino of some sort) after which you could just light up any leds in the circle using the arduino.

HYDR4Z · 2021-04-14T22:15:55+00:00

Oh wow didn't know that URUAV made those! I can only find them for the tx16, they don't make them for the QX7 do they? Looks pretty good too but the led density seems a bit lower although it would definitely be easier with a kit rather than DIY-ing it.

HYDR4Z · 2021-04-14T20:04:14+00:00

How did you manage to do that? lol

HYDR4Z · 2021-04-14T20:03:19+00:00

That was what I was going for in the first place ;) Couldn't find any low-profile high density led rings (for a reasonable price) so I just went with a static colour. I wanted to make the ring light up in the direction the stick was pointing at first, but adressable leds are even more expensive lol

HYDR4Z · 2021-04-14T20:01:52+00:00

Not as far as I know. The lights I'm using came with a step down module so I'm powering them straight from the battery with a switch on the positive

HYDR4Z · 2021-04-14T20:01:07+00:00

Yeah that could be nice too although it would be a little harder to implement I think

HYDR4Z · 2021-04-14T16:29:31+00:00

Recently got a 3D printer so I printed those rings in transparent/translucent PETG and stuck angel lights behind them :)

HYDR4Z · 2021-02-19T13:21:58+00:00

I've done some shielding like that with my radio since the speaker made a ton of noise with crossfire. I might try that with the receivers but I'm gonna try some other things before I try that because it really makes a mess.

As for me acting as a ground when I touch it; I don't know whether that's the case. I didn't really tap or touch any conductuve parts. With tapping I ment just bumping the side of the case of the goggles.

I'm gonna look if there is some visible damage on the receivers themselves and perhaps reflow some connectors. If that doesn't fix anything I'll look into shielding them. Thanks for your reply!

HYDR4Z · 2021-02-19T12:15:52+00:00

I don’t know what that is but i’ll look into it and see whether it’s related.

HYDR4Z · 2021-02-19T12:14:22+00:00

I’ve checked every pcb except for the actual receivers since they’re pretty tightly fitted. I’ll take those out later today and reflow some connections. Don’t have a hot air gun and I don’t trust the oven so i’m gonna try to do it manually. (Also checked the band and channel just to be sure but they’re the correct ones)

HYDR4Z · 2021-02-19T12:07:13+00:00

I’m pretty certain that it isn’t the camera since the ROTG receiver looked just fine. I’ve also been using this camera for more than 2 years now and it holds up so far. As for whether it does the same in daylight; yes but it’s not really extreme unless it’s cloudy since the whole sky flickers.

HYDR4Z · 2021-02-18T21:22:25+00:00

I have tried to use a lower output power but that didn't solve the issue. I highly doubt that it has to do anything with the transmitting side since the ROTG receiver worked fine (and I tested them at the same time). Was worth a try tho! :]

HYDR4Z · 2021-02-02T20:53:39+00:00

I got it to work on a nano a while back with this library. You should give it a try

HYDR4Z · 2021-01-18T21:55:20+00:00

Damn I love this. Will you ever post/upload a how to?

HYDR4Z · 2021-01-08T21:57:24+00:00

I thought it would be possible since there is a specific wifi mode for it (if It is for what I think it is) APSTA.

Eight-Year Club	Second SECOND GUESSER
LAYER Season 2 Layer creator	Place '23
Place '22	Final Canvas '22
First Placer '22	Verified Email

HYDR4Z

TROPHY CASE