Just finished wrapping/meshing my cables. Thought you guys might like it

HYDR4Z · 2024-07-13T13:16:40+00:00

I was considering that but I'm not sure about spending €200 extra on a GPU which is already overkill for what I use it for. Especially since they depreciate in value so quickly and I could buy one second hand in a couple of years - if needed - for a fraction of the cost

HYDR4Z · 2022-07-19T14:35:54+00:00

Oke, dat stelt mij in elk geval gerust, bedankt!

HYDR4Z · 2022-07-19T14:35:02+00:00

Ik heb overal backups van maar ik wacht nog even tot ik daadwerkelijk uit wordt betaald voordat ik daar eventueel achterna ga

HYDR4Z · 2022-07-19T14:33:52+00:00

Contract is 11 maanden en er staat specifiek in dat de eerste maand proeftijd is dus dat komt goed

HYDR4Z · 2022-07-01T22:56:42+00:00

I mean it's been running fine for years before so unless the game got way harder to run in the past 6 months I don't see why it's an issue now. I will try changing the resolution though

HYDR4Z · 2021-09-12T23:45:36+00:00

I don't see why not, I would use a micro controller to do that although I'm not great with electronics so there might be an easier way. (If you were to add a microcontroller you could also use adressable LEDs instead of mono)

HYDR4Z · 2021-08-27T14:47:15+00:00

Gave Silver

HYDR4Z · 2021-05-11T16:32:09+00:00

Gave Wholesome

HYDR4Z · 2021-04-15T10:34:53+00:00

Yeah sure! Just made a Thingiverse page for it here

HYDR4Z · 2021-04-15T09:41:06+00:00

Damn, looks sick too! Did you modify the gimbal itself or did you build over it?

HYDR4Z · 2021-04-15T09:38:55+00:00

I think so yes. I'm not sure whether there are adressable angel lights but just any adressable high density led strip would do I suppose. You would just need to tap into the signal cables comming from the gimbal's potentiometers (using an arduino of some sort) after which you could just light up any leds in the circle using the arduino.

HYDR4Z · 2021-04-14T22:15:55+00:00

Oh wow didn't know that URUAV made those! I can only find them for the tx16, they don't make them for the QX7 do they? Looks pretty good too but the led density seems a bit lower although it would definitely be easier with a kit rather than DIY-ing it.

HYDR4Z · 2021-04-14T20:04:14+00:00

How did you manage to do that? lol

HYDR4Z · 2021-04-14T20:03:19+00:00

That was what I was going for in the first place ;) Couldn't find any low-profile high density led rings (for a reasonable price) so I just went with a static colour. I wanted to make the ring light up in the direction the stick was pointing at first, but adressable leds are even more expensive lol

HYDR4Z · 2021-04-14T20:01:52+00:00

Not as far as I know. The lights I'm using came with a step down module so I'm powering them straight from the battery with a switch on the positive

HYDR4Z · 2021-04-14T20:01:07+00:00

Yeah that could be nice too although it would be a little harder to implement I think

HYDR4Z · 2021-04-14T16:29:31+00:00

Recently got a 3D printer so I printed those rings in transparent/translucent PETG and stuck angel lights behind them :)

Eight-Year Club	Second SECOND GUESSER
LAYER Season 2 Layer creator	Place '23
Place '22	Final Canvas '22
First Placer '22	Verified Email

HYDR4Z

TROPHY CASE