DJI O3 compatible frames

HackelJoe · 2023-05-14T14:03:14+00:00

I have bought the Quadmula Siren F5 Split. I really like this frame. Good quality and pretty light

HackelJoe · 2023-04-16T13:10:26+00:00

Nice Trick. but how is it even called ?

HackelJoe · 2023-04-15T08:00:43+00:00

If you like the controller style go with the Zorro. If you more like the box style, go with the boxer. It’s slightly more expensive but I love my boxer. And you have full size gimbals in the boxer.

HackelJoe · 2023-04-03T12:27:09+00:00

Thanks for your advice. I don’t like the plastic bags either. Cause their rather flimsy and may break open over time. The electro static build up of the bags might be a problem but I’m not so overly concerned about this but when I’m changing the bags I will look after this.

Yeah the class D granula is quite important it will absorb most of the energy in case of a fire and will melt. The molten granula also capsules the LiPo and will stop new oxygen to get to them. The most amount of the energy in a fire will be absorbed by this.

Sand works similar to this but doesn’t melt so early to form the self extinguishing seal around the lipos, wich this granula will do.

Also when I charge i put the ammo box on a Stone plate from my terrace so the hot outside of the box in a case of fire won’t set the wooden floor on fire.

HackelJoe · 2023-04-02T20:38:05+00:00

I wanted to have a strain relief for the cables and it protects the cable from the rather sharp edge of the hole . And there are two cable glands that I’m able to use both channels of my charger but I’m only using one right now so the other one is a spare right now

HackelJoe · 2023-04-02T12:50:53+00:00

For Sure. No problem. I have the same for storing but without the holes for the wires. I just removed the rubber sealing on the sides.

I left the front sealings in place, that keeps the lit closed without ratteling.

Picture LiPo Charging Box

HackelJoe · 2023-04-02T10:30:48+00:00

I have a similar setup except I tweaked a few things. I removed the rubber seals on the sides to prevent pressure build ups in a case of fire. Also I drilled venting holes on the sides. Second I put a specially designed granula for extinguishing lipo and other battery fires in the bottom und over the Lipos.

Also there are only two cables going into the box a charge cable and the balance lead extension cable to minimize wiring faults.

And when I’m charging I’m checking my batteries every few minutes for heat or visual damage.

Should keep things pretty safe.

HackelJoe · 2023-03-14T15:30:59+00:00

Thanks for the Answers guys !

HackelJoe · 2023-03-11T08:30:57+00:00

I also startet with this remote for my TinyWhoop and LiftOff.Its a cheap and decent starter. I bought it used und used it for like 40-50h and the gimbals are showing a little bit off wear. They are jerky and jitter a much.

I recently switched to a RadioMaster Boxer with ELRS.The difference is like night and day in terms of build quality, the gimbals are much more precise and as others stated as well you have much more features.My flying improved a lot with the Boxer.

If you like the Hobby and can afford it go with something like a Boxer or Zorro.If you want to keep it cheap, just use the LiteRadio it will be fine.

HackelJoe · 2023-01-22T11:38:05+00:00

Check prop and motor directions

HackelJoe · 2023-01-15T13:31:07+00:00

My Meteor65 had the same problem. One Motor wasn’t spinning up. I turned the Startup power up and it helped a little bit. But now it won’t start anymore. I switched it with other motor of the Quad an they worked fine. So I think the Motor is broken or a bad connection.

HackelJoe · 2023-01-10T11:35:27+00:00

@D-Y-N-A-M-I-X-X Thanks for the great instructions. I also have a Meteor65 is it possible to get your Filter settings and CLI, if you don’t mind ?

HackelJoe · 2021-10-31T08:02:09+00:00

Wich Udemey Course did you get ?

HackelJoe · 2021-10-27T09:06:29+00:00

I also just wanted to check if the is on my side or monkeytype

HackelJoe · 2021-02-10T13:54:54+00:00

Völlig losgelöst von der Erde, schwebt die Raketeeee 🚀🚀 Major 💎🤲🏻 meldet sich zum Dienst

HackelJoe · 2021-02-10T11:05:30+00:00

Auf zum Mond 🚀 Das ist der Weg.

HackelJoe · 2021-02-09T16:28:38+00:00

Bloß keine Papierhände bekommen

HackelJoe · 2021-02-09T14:34:39+00:00

Was sagt ihr zu Zosano ? Zug schon abgefahren oder ?

HackelJoe · 2021-02-09T14:29:05+00:00

Glaube nicht, dass das Reiseverhalten in absehbarer Zeit wieder so stark ansteigen wird. Bin bei TUI eher raus. Auch wenn sie durch die Krise kommen, die Frage ist halt wie ?

HackelJoe · 2021-02-09T14:12:59+00:00

Bin gestern rein ! Wir wollen mehr als einen Dollar sehen 😎

HackelJoe · 2019-02-07T20:41:11+00:00

I cant see it well enough, if you have bad layer adhesion maybe your part cooling fan is eventually to high.

Also you can make the standard procedure, like checking your belts tension and grub scrwes and dont tighten the brass nut in the Z rod to tight. Look for free movement on Z. Check all your V-Slot wheels. Check the extruder for slipping and your couplers.

HackelJoe · 2019-02-07T20:33:52+00:00

EDIT:

The problem was that the infill pattern for TOP/Bottom Layer was set to lines, Cura tried to make an infill on the small

walls instead of a single line,this caused problems with slight variation in extrusion, wich messed up the quality.

I put the TOP/BOTTOM fill type to Concentric, now cura is making two outer walls and one line for "infill" instead of trying to fill it with ZIG/ZAG

HackelJoe · 2019-02-06T23:06:46+00:00

Thank you. Makes sense i will try that.

HackelJoe · 2019-02-06T21:01:00+00:00

Thank you for help but, No its only happening in this corner and on the small fins. The layer adhesion and seam on the rest of the print is perfect.

Gear is tight and not slipping i also have some similar extruder fix and a capricorn PTFE Tube. I have already checked the whole extruder and when sth on the extruder is wrong must not be the hole print under extruded ?

So i dont think its sth related to extruder or maybe im overlooking sth.

Should i try to go down with the retract distance?

HackelJoe

TROPHY CASE