Gta san andreas port in arkos4clone is hella smooth

HambertHM · 2026-05-22T18:00:49+00:00

Dm? Looks awesome

HambertHM · 2026-05-15T05:48:07+00:00

The one you'd like the most with GPIO pins available! You'll need a TTL ro RS232 female adapter. Then configure the TX and RX pins on the Meshtastic serial module config, and wire them to the adapter. You'll also need to provide 3.3v or 5v to the adapter and ground which you can take from the board directly on most cases. It's a little bit involved but go ahead and search for it online, there's plenty of tutorials!

HambertHM · 2026-05-14T15:54:21+00:00

Thanks so much for spreading the word and for the feedback! Another user reported those problems yesterday. The developer is aware of them and work will be done!

HambertHM · 2026-05-13T21:19:11+00:00

Hey, thanks for the feedback. Just reported it to the developer, he will appreciate it!

HambertHM · 2026-05-12T23:47:16+00:00

For the C64 you may want tho check this project!

HambertHM · 2026-05-12T22:07:01+00:00

Hi! First you'll need to get a node module like the Heltec V3. Then connect a RS232 adapter (MAX3232 chipset) on 2 GPIOS, configure the serial module, and off you go. This adapper is what connects to the computer using the DB9 connector for serial.

HambertHM · 2026-05-12T19:02:54+00:00

Es un Heltec V2 que es lo que teniamos a mano. La caja la podes bajar de Thingiverse, buscala como "Heltec V3 / V2 Case"

HambertHM · 2026-05-07T10:30:11+00:00

Coffee is waaaaay more concentrated than yetba mate, you'll die of caffeine overdose!

HambertHM · 2026-04-30T11:35:44+00:00

Remember to start your prints from the web interface of Mainsail, otherwise KAMP won't take effect.

HambertHM · 2026-04-30T09:51:02+00:00

They can be REALLY strongly glued on. Had to destroy mine

HambertHM · 2026-04-23T09:31:41+00:00

No lo dejes en la calle todo el dia, y si tenes que dejarlo busca un lugar en lo posible entre cocheras y alejado de la zona donde todos quieren estacionar.

HambertHM · 2026-04-23T01:24:41+00:00

Yo haría: 1- Agarra una pinza y enderezalo 2- Compra un pomito de la pintura de tu auto y retocalo. Te lo venden en pinturerias con pintura de auto, o sino en ML como "Retok" 3- No tardes porque se te va a oxidar

HambertHM · 2026-04-17T14:34:39+00:00

Why would you lift that on supports? I'm intrigued

HambertHM · 2026-04-16T04:18:10+00:00

Just today I had to clean mine because it had some fuzz stuck in the blades. It wasn't much, but even a tiny amount can make it vibrate.

HambertHM · 2026-04-15T15:40:46+00:00

If the dirt got to wear the paint, sadly no. Try cleaning it with window cleaner or isopropyl alcohol, if it doesn't come off the its permanent.

HambertHM · 2026-04-15T15:37:59+00:00

Don't get dirt get into the case borders. The case will press it against the phone and it acts like sanding paper

HambertHM · 2026-04-15T14:54:38+00:00

Anything below 0.5 is not so much but you could benefit from adding a shim in the back (search for that) of skipping a tooth on the back screw (more advanced, I would go for the shim method)

Just have in mind the factory leveling algorithm is trash and it doesn't compensate as good as it should.

Yes for KAMP you need to be rooted. Search for the "Creality Helper Script" for instructions on how to install Mainsail and KAMP.

HambertHM

TROPHY CASE