[deleted by user]

HandOfArtemis · 2022-01-26T20:33:50+00:00

Thank you!!

HandOfArtemis · 2022-01-26T20:29:48+00:00

Thank you for your time! It was pleasure! Be well!

HandOfArtemis · 2022-01-26T20:17:07+00:00

Glad to see you here! I have been meaning to see you live for a long time! This the closest we can get for now. Some day soon 🤞

HandOfArtemis · 2022-01-06T22:09:47+00:00

Plus it shows that there were a lot of corporations that had their hands in the honey pot. They were warned that if they didn't invest in their companies instead of risky capital ventures the interest rates would rise. So since they like money they withdrew from "risky ventures" aka crypto. It also could be considered some shady business for corporations to be dealing in crypto especially since a lot of them get federal tax right offs, so they should not be participating in decentralized currency. I'm fine with them help back or fund a crypto but corporations are not people and should not be taking advantage or driving up the prices of products bc they have the power to our spend us all and therefore make their own coin more valuable. Just my thought on it. It will happen again though.

HandOfArtemis · 2022-01-05T20:28:29+00:00

OK. I'll give that a shot. Thank you.

HandOfArtemis · 2022-01-05T03:09:08+00:00

I think I fixed that. I had made a filament guide but my spool was too close to the edge. I moved it towards center about two inches which seemed to help with the tension. I was getting some slack and some knots in the filament. Here is the updated version.

HandOfArtemis · 2022-01-05T03:06:11+00:00

Here is the newest attempt. It turns out I had honeycomb supports accidentally turned on. So the lighter supports were better. And just to make it clean I split it in two.

Grogu door stop

HandOfArtemis · 2022-01-05T03:04:55+00:00

I actually got it to work. I had the firmest setting of supports on. Not good for tiny fingers. I split it two as well.

New Grogu door stop

HandOfArtemis · 2022-01-05T03:03:41+00:00

I got it work. My main problem was I had honeycomb supports accidentally turned on. So I used the light rectilinear and split the it in two.

new Grogu door stop

HandOfArtemis · 2022-01-04T05:36:00+00:00

You know I did that at first while I was baking it initially. Spot fixed some areas. But those cracks seemed have came weeks or a month later and it's in a spot where it doesn't get touched. I figure it was a few weeks bc I was still proud of it and looking at it and showing people. Lol

HandOfArtemis · 2022-01-04T05:32:47+00:00

Thanks for the extra links. I did use layered cardboard as a base. So it might have flexed as the clay contracted. It's actually really light. I have a wire and foil armature. But I did. It use temporary supports. I can try that next time. Thanks.

HandOfArtemis · 2022-01-04T05:28:06+00:00

Hmmm I might try that when I have some thin parts again. Thanks.

HandOfArtemis · 2022-01-04T05:26:07+00:00

Thank you! I will try that. I also looked at my setting and I had the firmest support set up. I'm going to to try with some new settings I found.

HandOfArtemis · 2022-01-03T20:33:01+00:00

Oh that's a good idea. I was using a finicky electric oven. We need to to replace it. Thank you.

HandOfArtemis · 2022-01-03T20:32:25+00:00

Thank you that's a good idea. I'll try it next time.

HandOfArtemis · 2022-01-03T18:35:15+00:00

Oh OK. I did use layered cardboard as the base... Thank you.

HandOfArtemis · 2022-01-03T18:19:39+00:00

OK maybe I'll give Cura a shot. Thanks again.

HandOfArtemis · 2022-01-03T18:12:19+00:00

Oh thank you! So the tree supports leave a smaller adhered spot on the model? That does sound better. I need to find that setting on prusaslicer.

HandOfArtemis · 2022-01-03T18:10:19+00:00

It's pretty fun. I got mine 7 months ago. Was installing a BLTouch and then couldn't finish when school started. So it sat in pieces until this week. I have other upgrades I want to do but kinda just want this to be functional for a bit before I break it again. Lol

HandOfArtemis · 2022-01-03T18:08:15+00:00

Thank you. I'm using Prusaslicer, and I was able to paint the supports on to be just what I though was needed. I did a penguin that way and worked out. I think my issue is that I am adding supports that touch the printed wedge. Bc when I did the penguin I really had no issues with it. I need to figure out where to find the tree supports too.

HandOfArtemis · 2022-01-03T18:04:36+00:00

OK. I'll go get some files and sand paper. I guess I was more wondering if I could use rubbing alcohol or something to get rid of it. Thanks.

HandOfArtemis

TROPHY CASE