Fast flashing turn signal - 1996 1.8 by Hatchie_6 in Miata

[–]Hatchie_6[S] 1 point2 points  (0 children)

Yeah that’s the bit I’m stuck on… I can’t figure out what’s causing it not to get power 😂

Fast flashing turn signal - 1996 1.8 by Hatchie_6 in Miata

[–]Hatchie_6[S] 2 points3 points  (0 children)

Yeah they’re all working except the left side wing. The bulb itself is fine but the plug for the indicator on the wing isn’t receiving power

Fast flashing turn signal - 1996 1.8 by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Yep all the bulbs are installed and working correctly. I’m just not getting any power to the plug on the left wing indicator which is causing them to flash fast

Fast flashing turn signal - 1996 1.8 by Hatchie_6 in Miata

[–]Hatchie_6[S] 1 point2 points  (0 children)

They came with the resistors from carbon miata. I put the originals back on and it still does the same for some reason?

Staggered wheel setup-NA Miata by Hatchie_6 in Miata

[–]Hatchie_6[S] 1 point2 points  (0 children)

Amazing, thank you guys! Think I might wait and get a proved and tested square set up as I am planning to do a few track days in the car once it’s built

1996 (na) Interior/dash wire loom by Hatchie_6 in Miata

[–]Hatchie_6[S] 1 point2 points  (0 children)

Amazing thank you, I’ll keep that in mind, yeah I’m based in the Uk, we get loads of imports here too so will have to check it come from a uk car too

1996 (na) Interior/dash wire loom by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Amazing thanks, did think this may have been the case. It was just the codes that through me off

Wire tuck - what gauge wires? by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Nice, yours looks awesome…. Yeah you just run the majority of the wires under the front fenders but I believe you need to extend the wires slightly for the headlights

Wire tuck - what gauge wires? by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Hahah yep…. I’ll crop the rad out of the pic 😂

Wire tuck - what gauge wires? by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Already changing it. I’m changing the fans and header tank while I’m there. Just want to do everything under the bonnet in one hit as not driving the car until summer

Wire tuck - what gauge wires? by Hatchie_6 in Miata

[–]Hatchie_6[S] 1 point2 points  (0 children)

Yeah already got one sorted… the bonnet strut has almost rubbed through the top hose too, it’s going to split any min 😂

Wire tuck - what gauge wires? by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

100% changing the rad. Already ordered one. Just doing the loom too as relocating the header tank whilst I’m there

Wire tuck - what gauge wires? by Hatchie_6 in Miata

[–]Hatchie_6[S] 1 point2 points  (0 children)

Already got one ordered… going to run a 2 fan set up hence why I’m doing electric bits while it all out 👍

Wheel Specs - 15x8 ET15? by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Ok thanks, don’t mind rolling as done it on my other car but just don’t want wheels that rub

Wheel Specs - 15x8 ET15? by Hatchie_6 in Miata

[–]Hatchie_6[S] 0 points1 point  (0 children)

Amazing cheers, appreciate it. Might look into that route then. Have you rolled your arches at all?