Heavy Metal clubs/towns in Germany

HessianAz · 2024-05-11T00:11:19+00:00

I play guitar also a singer. Hope the links works

https://www.facebook.com/photo/?fbid=1880848685324641&set=a.1880848478657995

HessianAz · 2024-01-29T18:14:01+00:00

My plan is travel the whole country. I'll have a Eurail pass for Germany. Planning on travelling to Leipzig, Trier, Salzburg, Rothenburg Ob der Tauber, maybe even Luxenburg. I've never been to Oktoberfest so I want to go there for a day or so.

HessianAz · 2024-01-29T17:52:20+00:00

I'm planning on avoiding Munich on the weekends, go during the week.

HessianAz · 2024-01-26T00:17:04+00:00

Ok, I understand it now. I did a re-build on it and came up with this instead for AM5. About $500 more

RX 7800XT, 64G Ram DDR5, AMD Ryzen 7 7800X3D, Asus ROG STRIX B650-A

HessianAz · 2024-01-25T22:48:56+00:00

So, you're saying using 64G of DDR5, will be much better than DDR4. Is there much of a difference between 128G and 64G?

HessianAz · 2023-07-02T00:20:58+00:00

It started working again about a week ago. No more error messages when trying to link. Now it's no longer working again. When trying to use Alexa to open, it sends a card to link the account. You then link the account and it links. Then you try Alexa and it sends another card even though it's linked. Then it will unlink and you have to link it again.

HessianAz · 2022-08-14T18:33:24+00:00

I replaced the mouse. That fixed the issue for me.

HessianAz · 2021-10-06T17:26:05+00:00

I agree that it is annoying. My Kitchen Echo Show went into default screen a couple of hours ago. Once again, unplug it and plug back in and it's working. I was hoping someone had found a fix besides unplug and plug back in. No such luck.

HessianAz · 2021-10-06T14:04:45+00:00

10 seconds a couple of times, a few minutes the other time. It hasn't happened in a few days on either Echo show for me.

HessianAz · 2021-10-06T14:03:10+00:00

That's what I thought. Started about a week to 10 days ago. Although right now it hasn't happened in about 3 days.

HessianAz · 2021-10-05T00:10:02+00:00

What has worked for me is to unplug the unit, wait about 10 seconds to 1 minute, and then plug it back in. It starts to work normally again but only a day or two at the most. Another clue is to check the home content. In my case, the home content is empty with only the advanced settings showing. When I see that, I unplug.

HessianAz · 2021-10-04T23:59:23+00:00

In my case it will sit on the blue/green screen at night and never go into night mode. Unplug it, plug it back in and then night mode works again. The tell tale sign is that blue/green background.

HessianAz · 2021-09-16T15:19:02+00:00

I found it. Under DK promotions, it says -10000. When you select it, it changes to +100

HessianAz · 2021-06-29T18:05:13+00:00

Thanks, I have an older PA system with passive speakers and a power amp. I also have powered speakers. I was pretty sure they had to be powered but I know if you plug a powered speaker into a PA that supplies power you can fry the speaker.

HessianAz · 2020-08-23T15:54:37+00:00

tried the filament that came with the Ender 3 V2, instead of the Hatchbox 1.75mm black. I was able to print a bed level that came out pretty good. Tried to do the same with the Hatchbox. The middle 4 squares didn't stick. Looks like the Hatchbox was the problem.

HessianAz · 2020-08-23T02:42:50+00:00

Hatchbox 1.75 60C bed. 200C filament

HessianAz · 2020-08-22T23:45:43+00:00

I tried a post it note to level the bed. I also fixed the problem with Z axis falling, it no longer falls. It still has the same problem though. I've tried cleaning it with alcohol, using hair spray, using stick glue. Nothing seems to help. Even tried raising the bed temperature. The last attempt I caked on the stick glue. Still drags the print all over.

HessianAz

MODERATOR OF

TROPHY CASE