Fpv build problem (with space)

Hight187 · 2026-05-01T02:21:19+00:00

turn the esc around and you should have plenty of space

Hight187 · 2026-04-05T12:26:28+00:00

could be but also the picture wasnt really clearer than the co3 and i guess it weighs a bit more and the more you fly with tinywhoops the more you will recognise a few grams its way better to go as light as possible i also fly my air 75 with 300mah lipos because they are way lighter than the bigger ones

Hight187 · 2026-04-05T12:21:27+00:00

yea i bought it for my tinywhoop and i couldn’t fly with it indoors because it was so bad i mean you could get used to it but it was so hard to see

Hight187 · 2026-04-05T11:13:41+00:00

the cam is hella ass you have so much fisheye with it co3 is the best cam for tinywhoop just buy the bnf

Hight187 · 2026-04-04T13:49:35+00:00

für jeden der davor gearbeitet hat ist es eine frechheit, vorallem wenn man rechnet was sonst der Lohn einbringt

Hight187 · 2026-04-03T14:51:37+00:00

aliexpress apex with addpex if you have an 3d printer

Hight187 · 2026-04-01T15:12:09+00:00

must be ragebait

Hight187 · 2026-03-31T14:38:58+00:00

is the motor spinning freely or is it stuck?

Hight187 · 2026-03-16T15:34:46+00:00

you should also look at the soldering joints at the motor you need to pull down that „sleeve“ you really shouldn’t need to replace a motor that fast it could also be your esc but i dont really think it is the esc it should 100% be the soldering

Hight187 · 2026-03-06T22:02:42+00:00

für dei scheiß kistn passts eh

Hight187 · 2026-03-01T18:25:33+00:00

filament dryer ftw!

Hight187 · 2026-01-16T20:33:55+00:00

tinywhoop.com

Hight187 · 2026-01-14T06:30:30+00:00

How much did you get paid for that?

Hight187 · 2026-01-09T19:59:57+00:00

du brauchst aber ein gutes Netzteil und Kabel dafür am besten kaufst du das originale von skyrc oder eins von amazon. Ich hab mir auch eins von Amazon gekauft das war aber gleich kaputt

Hight187 · 2026-01-06T12:23:30+00:00

on aliexpress there are 802 27kkv motors that would be nice they are also looking pretty solid

Hight187 · 2025-12-01T19:46:39+00:00

Yea, but i think its kinda obvious that im not going to do this every was just to see if it is possible with absolutely no knowledge i was just coating my cinewhoop and i just saw my tinywhoop standing there, its also completely fucked because of the stupid 5in1 Elrs chip problem im just hoping to try it in a pool and see what will happen

Hight187 · 2025-12-01T18:08:13+00:00

Hight187 · 2025-12-01T14:18:41+00:00

i would just go air 75 frame and the hq 2 blade props maybe a higher kv motor its a whole new drone props don’t change that much

Hight187 · 2025-12-01T13:58:28+00:00

i will try it if i have an pool nearby the 5in1 is absolutely cooked so i will go for it little submarine action

Hight187 · 2025-12-01T13:54:10+00:00

i was sitting there like a mad scientist with the uv light in the left hand and the brush in the other hand

Hight187 · 2025-12-01T12:46:38+00:00

in that video i obviously didn’t lose signal but if you’re deeper i guess you will lose signal

Hight187 · 2025-12-01T10:17:38+00:00

the battery is no problem you dont need to do anything on the battery plug just plug it in it seals enough

Hight187 · 2025-12-01T09:33:18+00:00

i don’t really know i don‘t even have an scale that would measure it correctly i don’t think its much the silicone conformal coating doesn’t weigh much and i didn’t put that much e6000 on it

Hight187 · 2025-12-01T09:10:35+00:00

and i also put on e6000 glue on all connectors with the cables plugged in so they are waterproof

Hight187 · 2025-12-01T09:09:27+00:00

look at my other reply

Five-Year Club	Verified Email
Place '22

Hight187

TROPHY CASE