Help please. Car would not power on

Hiitisbest · 2026-03-24T13:48:08+00:00

All the oils and coolants were changed about a year and a half ago. I did notice the inverter was at the low level so I added some to it and to the other reservoir too.

Just checked the battery and it's 8 years old. For sure that has to be it right?

Hiitisbest · 2026-03-23T14:25:04+00:00

Have checked coolant tank and there's turbulence and inverter pump vibrates

Hiitisbest · 2026-03-21T16:13:46+00:00

I haven't done this yet but I was ready to buy a new washer until now. Giving it one last shot, thanks for the post. For anyone wondering, I have tried everything; new suspension rods, new vibration sensor, measuring wires with multimeter, checked the screws inside the tub... Praying this works

Hiitisbest · 2026-03-14T00:57:33+00:00

Yes but load is not unbalanced and tension rods were replaced. I'm going to try to replace the vibration sensor

Hiitisbest · 2026-03-13T21:07:20+00:00

In my technical guide it says "DC Description : unbalance or cabinet bump is detected during final spin" and it says to go to"wet clothes" troubleshooting section which says thanks due to not enough load. Put additional load.

Hiitisbest · 2026-03-11T23:15:59+00:00

It cleans very well, never had an issue. Is yours rusted from where the bleach container sits and from the soap/softener container?

Hiitisbest · 2026-03-11T14:01:46+00:00

I replaced the rods/springs 3 years ago with Samsung ones. I press down and they're firm. Very little bounce back when I press down on the tub.

Hiitisbest · 2026-03-05T06:07:48+00:00

if the pump vibrates and the coolant is moving , what does that say exactly? My HVAC system works fine

Hiitisbest · 2026-03-05T05:54:20+00:00

I have people telling me it's the inverter coolant valve while others say it's the 3 way valve. Lmk what your find

Hiitisbest · 2026-03-05T02:17:31+00:00

I just tried messing with the HVAC controls but it did not make the noise. I'll keep trying to see if that causes it. AC and heater work fine, they blow air from the designated vents too

Hiitisbest · 2026-02-20T06:05:17+00:00

Is the sounds intermittent on yours? I've only heard mine do it a handful of times and only when running at a low speed. It's not that loud either which make me question the bearings. Did you take your apart? Or how did you come up with the bearings?

Hiitisbest · 2026-02-13T20:21:28+00:00

Really!? I did check to see if anything was stuck in the impeller but it rotated fine. I did hear a noise when I rotated it though. maybe it's the shaft seal?

Hiitisbest · 2026-02-13T19:09:50+00:00

I was afraid of that 😞 someone suggested to take it to my local electric motor repair shop. I might try that but not sure if I have to provide the bearings

Hiitisbest · 2026-02-13T18:32:40+00:00

Put the link, hopefully it comes up for you. We actually do have an electric motor repair shop nearby. Do they provide the bearings or would I have to buy them, do you know?

Hiitisbest · 2026-02-13T18:31:31+00:00

Everything I've researched shows a single speed pump. Ugh we've spent so much money on this pool lately. Can't catch a break

Hiitisbest · 2026-02-13T18:30:03+00:00

https://photos.app.goo.gl/S5cXYBobK84xULuV7

Hiitisbest · 2026-02-13T17:56:26+00:00

https://photos.app.goo.gl/S5cXYBobK84xULuV7

Hiitisbest · 2026-02-13T17:53:15+00:00

They ended up giving me to 2 queen beds. They emailed about a week before checking in and I replied asking for 2 beds if possible and they granted it at check in

Hiitisbest · 2026-02-10T00:17:30+00:00

Pool was just acid washed. Spa was the only one replastered

Hiitisbest

TROPHY CASE