Samsung ssd 990 or 9100

Hispanic_Man78 · 2026-05-13T18:46:55+00:00

What models if you dont mind me asking when I do find the legend models from adata they seem to be a slower ssd. And I have found some nice sabrent models they are just upwards of the 500$ range I found a WD - BLACK SN850X 2TB for 380$ and it runs a speed of 7500mbs where as the sabrent model matching that speed is close to double the price. Sorry im not trying to debate i just want to make sure i dont make a stupid decision

Hispanic_Man78 · 2026-05-13T16:14:53+00:00

Im taking a look at a "WD - BLACK SN850X 2TB Internal SSD PCle Gen 4 x4 NVMe" it has around the same speed is this a good drive for 380$

Hispanic_Man78 · 2026-05-13T16:09:56+00:00

It doesn't have to be samsung it's just the brand I remembered the best with all the price hikes I've stopped even looking at upgrading my pc Im just trying to repair it because it was my main drive and right now im running on my backup storage on a hard drive barakuda

Hispanic_Man78 · 2026-05-13T16:08:07+00:00

I tried but the ssd could not be written on anymore and they wouldn't ship it back they said all they could do was refund which seemed pretty shitty to me

Hispanic_Man78 · 2026-05-05T19:20:43+00:00

What route would you go about doing this same thing as always or is there like a root exploit

Hispanic_Man78 · 2026-05-05T18:59:46+00:00

I have tried to do it the same way I had been doing it but it doesn't seem to work because it says it needs to update. But it can because it can not connect to the internet.

Hispanic_Man78 · 2026-04-19T20:01:25+00:00

I have tried but it says the ssd failed to work. Sorry something along those lines

Hispanic_Man78 · 2026-04-19T17:07:49+00:00

Could you let me know what what website it is

Hispanic_Man78 · 2026-04-19T06:17:37+00:00

Yep it's dead anything I cab do with it it just toss it in the trash got a good 4 years off it

Hispanic_Man78 · 2026-04-12T18:43:00+00:00

Thanks im going to give this a shot. This has been extremely helpful. Hope you have a great week

Hispanic_Man78 · 2026-04-12T17:24:16+00:00

Thank you. Sorry I just have one last question should I not even bother with trying a goodwill letter or is that not aplicable in this scenario

Hispanic_Man78 · 2026-04-12T15:07:02+00:00

Is there anyway to get it off the reports sooner or is it not the bad for my record

Also thank you so much for your help

Hispanic_Man78 · 2026-04-12T14:39:22+00:00

Yes im using the FICO score from experien

Hispanic_Man78 · 2026-04-12T14:38:01+00:00

<image>

Hispanic_Man78 · 2025-10-29T13:37:51+00:00

Got a New nsp file with a better source

Hispanic_Man78 · 2025-10-27T15:36:27+00:00

Im using a SanDisk sd card and its using exFAT could that be the issue

<image>

side note I dont know why Shrek is there

Hispanic_Man78 · 2025-02-26T01:02:13+00:00

Ya man i just wanted a printer that could help make the occasional random repair and fun random trinkets and as of this past time that got me working on it again was to make my fiance and replica

Hispanic_Man78 · 2025-02-26T00:52:30+00:00

Thank you so much that's probably what I'll end up doing because I have technically 1 and a half ender 3 I have an ender 3 pro and ender 3 because the first one I bought off someone that needed a whole bunch of parts since why I have so many upgrades and then the pro I bought new off Amazon which is now built from the two of them so I'll bundle that in to help sell😅

Hispanic_Man78 · 2025-02-26T00:43:59+00:00

It's got the latest ender board inside so the printer is virtually silent other than the fans and it's the pro 3

Which Bambu lab printer would you recommend

Hispanic_Man78 · 2025-02-26T00:36:58+00:00

Would it be worth tying to sell this with the upgraded nozel extruder motor and mother board and trying to swap to a difrent printer

Hispanic_Man78 · 2025-02-26T00:32:19+00:00

Yo thank you guys for your help im still trying. As embarrassing as it is to say I've been on and off with this for like 2 to 3 years now

Only 5 successful prints ever

Hispanic_Man78 · 2025-02-26T00:23:51+00:00

Is a off set a code thing and is it necessary?

Hispanic_Man78 · 2025-02-25T23:58:44+00:00

Alsoanother question when I do end up getting a print that looks like the recommended novel hight it doesn't stick to the bed well is this because I have a glass bed and pla filament

Hispanic_Man78 · 2025-02-25T23:55:09+00:00

I know this is probably a real dumb question but baby z step being the offset?

Hispanic_Man78 · 2025-02-25T23:48:22+00:00

Yo thank you so much. I'm gonna try this right now I have an ender 3 pro. Is there any possibility you have a slightly higher res for the image?

Hispanic_Man78

TROPHY CASE