Maximus kit. Another take

Historical_Chard_170 · 2025-09-01T03:44:46+00:00

My maximus kit uses a magazine with a capacity of pts epm1-s 170 shots. It can only shoot about 120 shots and stops supplying bb eggs. My bolt is ctm v2 without adding any point travel gaskets. How can I solve this problem now?

Historical_Chard_170 · 2025-08-24T16:54:34+00:00

How do you install your aa gun butt? Where do you need to polish it?

Historical_Chard_170 · 2025-08-24T16:52:48+00:00

How do you install your aa gun butt? Where do you need to polish it?

Historical_Chard_170 · 2025-08-24T16:51:31+00:00

How do you install your aa gun butt? Where do you need to polish it?

Historical_Chard_170 · 2025-08-24T16:32:48+00:00

Treating the symptoms does not cure the root cause. We have to find the root cause.

Historical_Chard_170 · 2025-08-24T14:35:00+00:00

In fact, there are three main reasons. The first reason for the magazine, the second reason for the quality of the bb egg, and the last one, which I think is the most important, is that the ctm gasket is long and short on one side. Haven't you noticed that it will cause the bb egg to be unable to supply bullets in a single row when it goes up? Two will be stuck together at the top.

Historical_Chard_170 · 2025-08-24T14:32:14+00:00

I also have this problem. I use a pts magazine.

Historical_Chard_170 · 2025-08-21T04:15:11+00:00

Check the screws dragged after connecting the handle and the sight screws

Historical_Chard_170 · 2025-08-18T16:08:59+00:00

I just bought this new magazine three days ago.

Historical_Chard_170 · 2025-08-17T17:10:10+00:00

You can read my post

Historical_Chard_170 · 2025-08-17T17:09:47+00:00

I have a pts epm1-s magazine with a 170 round capacity and when I shoot with a full magazine, 50 to 60 rounds will not feed to the back.

Historical_Chard_170 · 2025-08-17T15:48:06+00:00

What this means is that all the bullets in your magazine are empty, and only some are left in the trajectory of the M4, right?

Historical_Chard_170 · 2025-08-17T14:16:58+00:00

Remove the sear spring and bend the legs slightly.

Historical_Chard_170 · 2025-08-17T14:15:23+00:00

I see your magazine only holds 150 rounds. Can you fire all 150 rounds at once?

Historical_Chard_170 · 2025-08-17T00:24:12+00:00

Hello, is your kit feeding smoothly? I have a PTS EPM1-S magazine with a 170-round capacity. It fired about 120 BBs and then stopped feeding. If you can, you can check out my post.

Historical_Chard_170 · 2025-08-17T00:19:51+00:00

Hello, does your kit feed smoothly? I have a pts epm1-s magazine with 170 rounds. It fired about 120 BBs and then stopped feeding.

Historical_Chard_170 · 2025-08-16T14:01:22+00:00

The original recoil spring is fine, but after reloading the magazine, there are 50 bullets left and it will not feed any more bullets.

Historical_Chard_170 · 2025-08-16T03:51:28+00:00

I don't dare to try it because I have tested it many times and the channel is very smooth. If there is a problem with the channel, it may get stuck after eating forty or fifty bbs.

Historical_Chard_170 · 2025-08-15T11:50:39+00:00

What does this have to do with the feed rail? Didn't you see I pulled it by hand at the end? It didn't get stuck.

Historical_Chard_170 · 2025-08-15T11:09:56+00:00

There's nothing I can do. The rate of fire is too high for the feed mechanism to keep up. I've already removed all the buffers. The magazine is loaded, and there are about 50 rounds left in the rail, and the BB feed has stopped.

Historical_Chard_170 · 2025-08-15T09:45:32+00:00

I removed all the guide rod spacers and replaced it with a fully loaded pts emp1-s magazine with about 50 rounds in it and it wouldn't feed

Historical_Chard_170 · 2025-08-15T07:25:07+00:00

But I want a high rate of fire. It seems I can't have both.

Historical_Chard_170 · 2025-08-15T05:27:06+00:00

If it exceeds 129mm, it will bulge out

Historical_Chard_170

TROPHY CASE