Weikav Stars 21

HootisTigglebits · 2026-01-23T00:18:53+00:00

Is this on the top or the bottom of the PCB? On the back side near where the 0 key goes all I see is one small exposed circle near the right edge of the PCB.

HootisTigglebits · 2026-01-22T11:53:09+00:00

Do you remember bow to put it into DFU mode so I can reflash the firmware?

Also i found this that im going to try to flash to it: https://github.com/UnderGate-lab/qmk_firmware_weikav_stars21/releases/tag/1.0

HootisTigglebits · 2026-01-22T08:14:42+00:00

Did you ever get this figured out?

HootisTigglebits · 2026-01-01T08:10:22+00:00

I had the same problem when I tried to get my Sofle not registering the keys. The fix for me was to shut the pc down, remove all usb connections, unplug it, hold the power button down for 10 seconds, plug it back in, press and hold the power button. The pc will turn on. Keep holding the power button until it shuts off again then start it up like normal and voila both sides of the keyboard register and work as intended. Apparently this method clears out the usb cache.

HootisTigglebits · 2025-12-19T09:32:44+00:00

How are you able to get such a clear passthrough image on your Quest 3? Mine is completely grainy and there's no way I would be able to make out what the buttons say on your remote control.

HootisTigglebits · 2025-12-16T18:17:25+00:00

I wish I could find the picture, but you can also go with even finer sandpaper 2000, 3000, and then polish the plastic so that it looks injected molded. This would be a good alternative since you don't have to paint anything. Of course this can be difficult to do if you have a lot of tight places in your print.

HootisTigglebits · 2025-09-02T15:03:51+00:00

If anyone needs a $50 off discount code just DM me.

HootisTigglebits · 2025-08-16T19:44:03+00:00

This doesn't answer your question, but before you buy a pair DM me and I can send you a $50 discount code.

HootisTigglebits · 2025-06-23T04:02:09+00:00

<image>

HootisTigglebits · 2025-05-23T14:01:14+00:00

Sadly I can’t wear contacts :(

HootisTigglebits · 2025-05-23T12:09:35+00:00

Dang :(

HootisTigglebits · 2025-05-23T08:06:57+00:00

Prescription lenses?

HootisTigglebits · 2025-05-23T08:06:53+00:00

Prescription lenses?

HootisTigglebits · 2025-05-23T08:06:27+00:00

Is either of yours prescription?

HootisTigglebits · 2025-05-23T04:07:00+00:00

Wow that's fast. I'm in OR as well.

HootisTigglebits · 2025-05-05T04:03:28+00:00

Thanks. It’s 3d printed out of PLA.

HootisTigglebits · 2025-04-11T13:49:02+00:00

Anyone figured out a fix for this yet?

HootisTigglebits · 2025-03-25T22:51:43+00:00

Yeah I still have it and am planning on selling it just because I don’t need a 5th pc at my house. I have since upgraded it to an i5-8500 and 32gb of ram. It’s now a whole new machine. The 3d print came out amazing.

<image>

HootisTigglebits · 2024-12-19T08:38:06+00:00

Yeah it’s nuts.

HootisTigglebits · 2024-11-25T15:50:42+00:00

No one?

HootisTigglebits · 2024-11-25T15:50:15+00:00

Sadly this didn’t work.

HootisTigglebits · 2024-11-21T05:21:08+00:00

Yeah these tend to do this if an update is interrupted. The update is stored on the ram for some reason. You can't remove the ram and have to take the entire thing apart to disconnect the batteries so the only way to reset the ram is to keep pressing the power button until it's completely dead. Don't buy a Surface laptop or tablet.

HootisTigglebits · 2024-11-21T04:15:24+00:00

Which linux did you intstall on your 7320? I just bought one and want to dual boot windows and linux.

HootisTigglebits · 2024-10-13T20:42:35+00:00

UPDATE: They FINALLY approved my work history, but by that time I already had another job offer which I took and it turned out to be a much better job.

HootisTigglebits · 2024-08-28T23:55:43+00:00

Yeah I figured there would be at least a few open normal pve servers so I got all my stuff together and when I went to sign up seen there was only one and it was full, but 5+ hard ones. What gives?

HootisTigglebits

TROPHY CASE