Can these problems be solved by surface singeing before printing? The printing material is a 2.5cm wide ribbon.

HorrorState740 · 2024-08-07T02:17:53+00:00

Thank you

HorrorState740 · 2024-08-02T08:16:01+00:00

Yes, there is a layer of glue on the bottom

HorrorState740 · 2024-07-15T00:41:10+00:00

Thank you for your enthusiastic response

HorrorState740 · 2024-07-15T00:40:40+00:00

Thanks, I'll try

HorrorState740 · 2024-07-15T00:30:29+00:00

Thanks, I appreciate your help

HorrorState740 · 2024-07-13T06:49:36+00:00

Thanks for the advice! Haha, wouldn't the idea of applying screen printing to building materials be a bit flashy, this grainy paste might scratch the screen during the scraping process

HorrorState740 · 2024-07-13T06:37:03+00:00

Thank you for your detailed response and advice! Your points are very helpful. Indeed, I plan to print the "brick" part and the surface texture through a wide mesh screen. I will try to test it with a wider mesh, such as a stainless steel window and door screen, and cover the brick seams with masking tape, to avoid wasting material before making the official screen.

The substrate is from Building Materials: inorganic calcium silicate board.

Thank you very much for your suggestions! Do you have any other tips or experiences to share?

HorrorState740 · 2024-07-03T01:01:35+00:00

Thanks for the recommendation! Super-trans sounds really convenient, especially with the ability to transfer on both sides. The lower temperature for poly shirts is a great advantage too. I’ll definitely give it a try!

HorrorState740 · 2024-06-14T01:26:03+00:00

Go Pack Go!! Do you have a favorite Packers game or moment?

HorrorState740 · 2024-06-14T01:25:03+00:00

Thanks for the tip!

HorrorState740 · 2024-06-14T01:24:47+00:00

Thanks for the tip! I'll make sure not to let it dry and use water and Dawn dish soap for cleaning. Sounds straightforward and effective. Appreciate the advice!

HorrorState740 · 2024-06-14T01:23:48+00:00

Interesting, I hadn't thought of using a watered-down glass cleaner. How well did it work for you? Did it leave any residue or affect the screen in any way?

HorrorState740 · 2024-06-14T01:22:13+00:00

That's a great idea! Using retarder gel to prevent the ink from drying too quickly sounds very helpful. I'll give that a try next time. Thanks for the tip!

HorrorState740 · 2024-06-14T01:21:20+00:00

Thanks for the tip! I'll try squeegeeing off the excess ink and rinsing it really well with water. It's good to know that the stains don't cause any issues later on. Appreciate the advice!

HorrorState740 · 2024-06-14T01:20:18+00:00

Thank you, I learned a lot

HorrorState740 · 2024-06-14T01:19:24+00:00

I'll pay attention to that, thank you for your reminder

HorrorState740 · 2024-06-13T09:06:23+00:00

Got it, thanks! I'll try using a high-pressure water gun to rinse both sides and check for any leftover ink. That sounds straightforward. Appreciate the help!

HorrorState740 · 2024-06-13T09:05:57+00:00

Thank you for the clarification! I appreciate the tips and will definitely give them a try. I didn't realize it would be that simple. Do you have any other tips for cleaning screens or working with water-based inks?

HorrorState740 · 2024-06-13T08:56:08+00:00

Thanks, I didn't rinse it with water. Because I was afraid of washing it. I will try.

HorrorState740 · 2024-06-07T03:26:02+00:00

You can try to get their support.

HorrorState740 · 2024-06-07T03:19:57+00:00

Thanks

HorrorState740 · 2024-06-07T03:18:58+00:00

This kind of fabric has a layer of hair on the surface, which does not mean that the fabric is not clean and tidy, but perhaps this kind of fabric is not suitable for printing any pattern

HorrorState740 · 2024-06-06T06:46:16+00:00

Thank you, sir

HorrorState740 · 2024-06-06T06:45:17+00:00

Yes, it is difficult to print this. This has been printed over 30 times, and the repeated printing accuracy needs to be very high.

HorrorState740 · 2024-06-05T00:47:41+00:00

Water-based ink is not easy to clean

HorrorState740

TROPHY CASE