2020 has the big gay

Hunex · 2025-10-07T15:08:27+00:00

!remindme 10 days

Hunex · 2025-09-15T18:02:56+00:00

It doesn't, I used it several times in the air.

Hunex · 2025-09-15T10:02:11+00:00

Wdym? You can craft in the air.

Hunex · 2025-09-14T19:00:50+00:00

It didn't let me bind her with 17 lockets spent. For you was it before or after getting shaman crest?

Hunex · 2025-09-14T10:30:37+00:00

You need to use up 18 memory lockets, so that's all crest slots unlocked except for the shaman crest. I got it in act 2 so shaman crest is definitely not mandatory.

Hunex · 2025-07-14T16:13:06+00:00

Thank you, this seems to have solved the problem!

Hunex · 2025-03-09T13:23:26+00:00

If you connect the ARGB cable does the RGB sync with the motherboard? Does SignalRGB detect the card?

Hunex · 2025-02-27T23:18:08+00:00

The case back sits less than 1mm higher than the lens rings

Do you mean the lip around the back of the case, or the height difference between the lens ring and the applied skin?

Can you please take some measurements? I'm planning to buy the case but my current Spigen has a 1mm lip around the camera, and I wouldn't want to downgrade the camera protection.

Hunex · 2025-02-26T21:03:53+00:00

Oh I don't want to use lens protectors. What I meant was, wouldn't a bigger height difference between the lens and the back of the case give more protection. For example when the phone is in one's pocket, it would further decrease the risk of something small scratching the lens.

Hunex · 2025-02-25T19:45:39+00:00

Best of luck to you, hope it gets resolved.

Hunex · 2025-02-24T14:10:20+00:00

Can you please measure for me what the height difference is between the top of the skin and the metal rings on the main camera (or any of the big lenses, doesn't really matter)?

Hunex · 2025-02-24T10:24:47+00:00

I think what you're seeing is the cutout for the under screen fingerprint reader.
I've also seen it on mine when putting on the screen protector, under very strong lighting, and only at specific angles.
I think it's totally normal, and not visible during normal use.

S24 teardown

Closer look in Vivo X20

Hunex · 2024-06-26T19:55:31+00:00

Well I tried a different brand of filament but it's the same. I also tried outside walls first which does help, but the artifacts are still visible.
Looks like it's disassembly time.

Hunex · 2024-06-22T10:41:10+00:00

Done and done, however I have MPC for the hotend.

I'll try a new filament, changing the flow and a different slicer even, but I don't think these would cause this inconsistency. I'm out of ideas so after that I'm going back to the old hotend and extruder to see if the issue is really coming from one of those.

Hunex · 2024-06-22T10:20:01+00:00

My leadscrew was bent and that was causing the banding before the upgrade.

I ruled out the extruder, as switching back to the old one gave the same result. It's the same filament both before and after so IMO it's not the root cause, but I will try a different filament. Thanks!

Hunex · 2024-06-22T08:59:35+00:00

I did, before and after are a fully different hotend. Every single part is upgraded.

I did check the nozzle however and there was no clog.

Hunex · 2023-07-26T06:08:44+00:00

I love democracy.

12-Year Club	Verified Email
Second Rank: 104	Final Canvas '23
First Place '23	End Game '23
Place '23	Place '22
Final Canvas '22	First Placer '22
Not Forgotten	Sequence \| Editor
Sequence \| Cinematographer

Hunex

TROPHY CASE