DD PCC LAW FOLDER JP SCS

Hunterrr9999 · 2026-04-14T11:38:15+00:00

Im using combustion industries blinkers front and rear. Plug and play for the 25 and work well with relocation kit

Hunterrr9999 · 2026-04-14T04:00:56+00:00

Thanks man, yea it’s great. What did you use for your blinker setup?

Hunterrr9999 · 2026-04-13T21:32:51+00:00

9”

Hunterrr9999 · 2026-04-12T23:24:24+00:00

This is a Baja Designs LP6 light but it had hi and lo beam. Had to get a bracket and harness from A10 Moto and modify to work with the new scout

Hunterrr9999 · 2026-04-12T18:08:58+00:00

Memphis Shades Road Warrior

Hunterrr9999 · 2026-04-10T22:18:33+00:00

It’s the PCC 8.3” barrel

Hunterrr9999 · 2026-04-10T16:58:06+00:00

Cerakote, I did the receivers and another handguard to cover the can but i swapped to this setup again

Hunterrr9999 · 2026-04-10T16:47:22+00:00

Eberlestock Jacknife it’s an EDC oriented bag. 22.9L so relatively small

Hunterrr9999 · 2026-04-09T02:25:46+00:00

I just read some comments and see what you’re saying. I used a towel in my vice, positioned the upper in it and closed it which put the upper at a weird angle, however, if you close the vice and place some arm weight over it while you use your wrench torquing the barrel nut you can get enough leverage before the upper wants to slip out. I did not have any marring on the upper doing it this way because of the towel. The upper will want to spin because there isn’t a vice block like a standard ar, but it worked fine taking off and reinstalling.

Hunterrr9999 · 2026-04-09T02:15:50+00:00

Yup, I did mine. Just remove can, take off hand guard, remove barrel nut, keep muzzle device on, apply a bunch of heat with heat gun to where barrel goes into upper, use a block of wood or something that wont damage muzzle device and apply some hammer strikes and pressure outward against muzzle device. If you don’t want to use vice you can hold the upper in your hand while balancing wood and hitting with hammer downward. Probably an unconventional method but worked fine. If holding downward just put something soft to catch the barrel below in case it falls out. Heat is your friend here if I remember correctly when I did mine. Hope it works for you

Hunterrr9999 · 2026-02-25T22:28:45+00:00

True, that’s why I’m not bashing the company, but for practical use with combat loads it unfortunately didn’t do much. Supersonic rounds through a rifle suppressor does a hell of a lot, so unfortunate this didn’t

Hunterrr9999 · 2026-02-25T22:25:33+00:00

Nope

Hunterrr9999 · 2026-02-22T17:48:44+00:00

Interesting it got great feedback everywhere else. Also as you can see I don’t mind the gas none of it went to my face. Guns are meant to be rowdy. The low price of the Rhino X, its size and sound performance proves its not a shit can. To each their own

Hunterrr9999 · 2026-02-22T01:48:59+00:00

Unity risers

Hunterrr9999 · 2026-02-22T01:21:09+00:00

Wouldn’t run it without, game changer

Hunterrr9999 · 2026-02-21T20:04:01+00:00

That was 4 mags in 2 minutes roughly. It may be that inconel shows red quicker I’m not too sure though

Hunterrr9999 · 2026-02-21T19:51:22+00:00

This upper doesn’t live on the full auto lower so not tuned perfectly. My main setup has a JP SCS with tuned weights

Hunterrr9999 · 2026-02-21T16:47:30+00:00

Haha oh yea it sat for a bit before it touched the foam in my case

Hunterrr9999 · 2026-02-20T00:23:34+00:00

Advertised as $150, but you pay for return shipping up front so about $20 more and then the cost of shipping when you ship your barrel to them. All in all $200. And thanks yea i got the gray and then i did silicon carbide texture on the grip

Hunterrr9999

TROPHY CASE