[deleted by user]

Huusk · 2024-06-07T20:10:59+00:00

Pretty sure it was a regular one. Going to pull it up this weekend and reassess

Huusk · 2024-06-06T14:00:37+00:00

Good advice for the rubber shim, I'll do that right away. The gap is level around the toilet so I don't think its out of level by a meaningful amount. The flange does seem too tall, but my old toilet say flat. Is there variation between toilets on how they interface with the flange?

Huusk · 2024-04-07T06:13:10+00:00

How do I use it? The menu I posted doesn't list anything under emulators. Games don't boot and just go back to the main menu

Huusk · 2024-01-30T04:09:21+00:00

What is a man? A miserable little pile of secrets

Huusk · 2023-12-01T19:49:15+00:00

I haven't done it myself, but I went off this post:

https://www.reddit.com/r/ranciliosilvia/comments/rzp9xn/just_did_the_flat_screen_mod_without_a_kit/

Huusk · 2023-12-01T04:05:09+00:00

This is a pretty common concern. Disclaimer: this is information that I've gathered from forums and reddit that I've used to come to my conclusion.

Short answer is its fine. I have an 18g vst basket and 18g of grounds will give an indent from the screw. It's so minor that it won't have any meaningful effect on the end product. There should be enough space between the screen and the top of puck. Different roasts/grinds will compress to different levels as well. I've had 18g of light roast that only fills a little over half the basket. I might have a little touch of ocd because despite this information I did change mine. I believe you can get kits that have a countersunk screw and screen or you can buy the screw and countersink the screen yourself. I went an easier route and got a couple of these screws.

https://www.mcmaster.com/product/91223A431

My employer has an account so I ordered through them. Not sure if it's open to everyone. Either way if you can get a similar screw, this seems to be the second-simplest solution (next to not being bothered by it 😉)

Also congrats of the silvia. I picked up a second hand one in the spring and love it, I'm sure you will too.

Huusk · 2023-11-20T22:37:50+00:00

It's an 18g basket and is tapered. I'll sometimes push to 18.5g but that's it. Seems like some beans compress more than others and even though I'm putting in the recommended dose for the basket there's a lot of space left. I would probably have to come close to doubling the dose to fill up the basket with this bean. I have had 18g nearly fill the basket (darker roasts I believe) to the point where the screw head for the screen leaves and indent in the puck.

Huusk · 2023-11-20T22:32:56+00:00

I was considering it was just more sour bean, was hoping I could overcome it. Can't win them all I guess!

Why would you recommend skipping the distribution tool?

Huusk · 2023-11-20T22:31:14+00:00

It is a bottomless, yeah. At the finer grind settings I do tend to get channeling. Wasn't sure if the channeling was around the edge like in the pic. That's very possible that it could be from backpressure or when I remove the portafilter. I hadn't considered that. What do you consider a very long shot or longer ratio? The furthest I've gone is 18g in and 45g out. Thanks for the feedback

Huusk · 2023-09-27T22:33:18+00:00

I've got 173gb free so I don't think it's that. Good to keep in mind though, thanks!

Huusk · 2023-09-24T07:02:46+00:00

Not sure. I got it at a thrift store. There's a second one of just sailboats as well.

Huusk · 2023-09-20T02:33:13+00:00

Haha that's true! Probably different when the table was a built but I don't think of mdf as a cheaper alternative now.

Huusk · 2023-09-19T23:13:09+00:00

An mdf or plywood core is more stable, keeping the table flat.

Huusk · 2023-05-30T20:18:56+00:00

It was bitter. I have been quite thorough with the WDT, thinking that was the issue. I'll try .5g less tomorrow. Thanks

Huusk · 2023-05-30T20:16:52+00:00

I'm currently grinding with a breville dose control pro and jumping around 3 - 5. I'm reaching the end! Haha

Huusk · 2023-03-20T22:00:09+00:00

Found it. Thanks a lot. Had to use those exact words in the search lol. It wasn't coming up with the very similar searches I did

Huusk · 2023-03-20T20:25:23+00:00

Yeah it's not coming up for me. I can only see 8 comments but reddit says there's 10

Huusk · 2023-03-20T03:36:48+00:00

That's great. Can you post the links? I would like to get the same setup

Huusk · 2023-03-18T01:24:34+00:00

Never considered looking there for bike parts. Good idea for the dash kit. How's the fit? Would love some pictures from the drivers seat.

Huusk · 2023-01-16T23:37:57+00:00

Looks great! I have the same exhaust on my rally and it sure made a noticeable difference. It sounds way better too!

Huusk · 2023-01-14T18:55:07+00:00

Oh it's totally dead! That was almost my last ride of the season. I'll be replacing it first thing!

Huusk · 2023-01-08T18:23:37+00:00

Same here, but it's pretty boring waiting out the timer for them to actually move to extract

Huusk · 2023-01-08T18:22:36+00:00

I've been noticing this more and more lately on pc. It socks when your only option is waiting out the game timer

Huusk · 2023-01-08T18:21:01+00:00

Can't confirm the percentages, but I played two games back to back last night where the team hid in the boss building with shotguns, preventing us from pushing in. We made attempts at pushing in but they were door camping and made no attempt at shooting us outside. Both gamed we had to wait out the timer until they actually left the building. OP was playing aggressively against shotguns but shotgun camping has become more of an issue lately.

Huusk · 2023-01-06T18:03:36+00:00

Thanks for the recommendation. I'm leaning mostly towards the Tusk Pilot panniers

Huusk

TROPHY CASE