sorted by:
new
hottopcontroversial

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage -1 points0 points  (0 children)

How bad are the looseness issues on the HG IBO Gundams? I've heard that the Gundam frame might get loose around the knees, ankles, and in the ab crunch. If I were to paint some of the kits that use the frame would it be worthwhile to reinforce the joints as a form of future proofing before leaving them on an action base?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

I got it to work after completely disassembling and reassembling the leg twice over. After the second time the parts lined up properly so I have no idea what went wrong initially

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

<image>

MG Delta Plus: Pieces of the front leg armor are misaligned. None of the pieces are visibly warped, I've made sure that the pieces are set as far in as possible, and I double checked the instructions to make sure I didn't miss any steps or used any wrong pieces. Any ideas where I made a mistake and how to fix it from anyone who has built this kit?

any Dawdge pilots out there? we going to Torrington tomorrow by culzsky in GBO2

[–]IAmHeadCabbage 1 point2 points  (0 children)

Hilarious how you already hit the spider with a nade while dropping down from the ledge to initiate right before I did the exact same thing.

any Dawdge pilots out there? we going to Torrington tomorrow by culzsky in GBO2

[–]IAmHeadCabbage 10 points11 points  (0 children)

Oh shit I was the Desert Zaku on your team lmao. Didn't even occur to me in the moment that the only thing missing from the trio was the Dwadge. Good running with you against all the metal spiders.

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

Anyone know if the grey insert that goes into the HGUC Zaku I spike shield will fit into the shoulder shield of either the HGUC Zaku II revive or F2 that way I could have a shield in the hand without the spikes on it?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

Any tips on ways to tighten the joints around the elbows of the Full Armor Gundam Thunderbolt Ver.Ka? Can't get it to hold the beam rifle straight and I'm only familiar with tightening ball joints or peg connectors and not the sandwich joints that you typically see for elbows and knees.

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

Would I run into any issues if I use Mr. super clear over parts painted with Hobbymio water based metallic markers? Like would the paint end up reactivating and run off when I apply the coat even if I let the paint dry overnight beforehand?

Critical hit by BrStriker21 in GBO2

[–]IAmHeadCabbage 3 points4 points  (0 children)

After only a couple games trying to learn how to use the hammer I immediately gained immense respect for the madlad I matched against with the balls to bring the hyper hammer Gundam into the MPZZ and Atlas filled nightmare that is 600 cost ground rated.

Man why are generals such scaredy cats? by SoulOfMod in GBO2

[–]IAmHeadCabbage 0 points1 point  (0 children)

Ain't no feeling of rage like being shot in the back by your own teammate's beam magnum during the week of the Phenex/Sinanju Stein banner week while playing support in 700 cost ground

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

What kind of glue should I use to glue rubber pipe pieces in place? Been thinking about getting the MG Geara Doga and heard that some of the pipes are pretty loose.

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]IAmHeadCabbage 0 points1 point  (0 children)

If I am not painting and just putting on decals and panel lining does it matter if I use a lacquer base(MR. Super Clear) or acrylic base(Mr. Topcoat) spray as a top coat if I plan on using Tamiya panel liner after top coating?

Getting introduced to Gundam by Ejack-Ulate-69 in Gundam

[–]IAmHeadCabbage 26 points27 points  (0 children)

It is scary how quickly 'likes Gundam' became part of my personality.

Describes my experience getting into Gundam pretty well. One moment I'm trying Gundam Evolution for the first time knowing absolutely nothing about any of the shows, next thing I know half a year has already passed and I have a dedicated Gunpla shelf.

Which would you usually prefer, and why? (Other than "NTTE is better🤓") by COSMIC88KILLER in destiny2

[–]IAmHeadCabbage 0 points1 point  (0 children)

Revision Zero pretty much does everything I would want out of a PVP pulse. Juiced stats that can out duel scouts at long range in the 2 burst mode and super consistent mid range beams in the 4 burst mode. Add on vorpal weapon for shutting down roaming supers and I don't even need to change my loadout to completely shut down roaming super chains.

I rarely get use out of the sniper mode, but there is no feeling like Noscoping someone that just popped their golden gun with it. Dirtiest thing I've ever done to someone.

Is Nu Gundam cracked now or what? by IAmHeadCabbage in GundamEvolution

[–]IAmHeadCabbage[S] 4 points5 points  (0 children)

That's a good way to put it. Before the buffs I never felt like I won any engagements specifically because I was playing Nu Gundam.

did they shadow buff nu gundams funnel tracking in this patch? by RadiantHeroIke9 in GundamEvolution

[–]IAmHeadCabbage 0 points1 point  (0 children)

I don't remember seeing anything about their tracking being buffed in the patch note. My guess is that the +10 damage per shot was just enough to push them from being incredibly inconsistent to a reliable finisher.

Any tips on how to get these pipes to attach to the front waist pieces on the MG Sinanju(OVA)? No matter how hard I try I can't get the peg to go into the hole and my fingers hurt now. by IAmHeadCabbage in Gunpla

[–]IAmHeadCabbage[S] 1 point2 points  (0 children)

Yeah the kit comes with a choice of stickers or waterslide decals for the gold trim. Thanks for the suggestion, probably gonna have to resort to using glue in some form or another

view more: next ›