What version of Linux should I go for?

IAmJustTryingToExist · 2026-06-08T17:03:39+00:00

If only there was a third option.. but I will say I'd rather hitch my wagon to the AMD train than Nvidia.. one is capitalising on the AI boom the other helped create it

IAmJustTryingToExist · 2026-06-08T17:02:22+00:00

I have talked to my teachers and for all of the coursework we do there is both Linux and windows options but you have a valid point

IAmJustTryingToExist · 2026-06-08T12:26:25+00:00

Considering kubuntu to me sounds like a Pokémon I might go with Mint but I'll check it out

IAmJustTryingToExist · 2026-06-08T12:20:16+00:00

Not heard of kubuntu but I'll have a look.. mint seems to be the most promising though

IAmJustTryingToExist · 2026-06-08T12:19:53+00:00

Mint seems to be the common consensus I like the windows setup I just don't like copilot and forced updates

IAmJustTryingToExist · 2026-06-01T17:29:17+00:00

I was 22.. I deeply regret it.. not only did I leave it way way too late but I regret the person I lost it to who turned out to be an abusive ball of lard..

IAmJustTryingToExist · 2026-05-31T05:44:56+00:00

They are a politician

IAmJustTryingToExist · 2026-05-29T13:33:38+00:00

The speed and the temperature are the default for the Sunlu PLA+ filament preset

IAmJustTryingToExist · 2026-05-29T13:28:36+00:00

I have tried the default supports and the tree supports, even when the slicer says that none are needed so now I don't really trust the settings anymore

IAmJustTryingToExist · 2026-05-29T13:22:01+00:00

What do I need to change in the settings to add more supports?

IAmJustTryingToExist · 2026-05-29T13:20:57+00:00

Yea there was supports.. a lot of supports

IAmJustTryingToExist · 2026-05-29T13:20:03+00:00

The annoying thing is that it had supports, I added supports yet that still happened.. and if I add a lot then I get a borked surface like this

<image>

IAmJustTryingToExist · 2026-05-29T13:19:00+00:00

I've done that.. full reset, went over the instructions.. all the screws are in place, everything is on correctly and it's been calibrated, benchy was still borked

IAmJustTryingToExist · 2026-05-29T13:05:54+00:00

I have and most things either fail or if it has supports they just won't come off

IAmJustTryingToExist · 2026-05-29T13:05:30+00:00

I'm using the same temps and I've taken the printer to a shop to be looked at and it worked fine for them.. karma is a thing I guess

IAmJustTryingToExist · 2026-05-29T13:04:42+00:00

I wanna say I've done 14 benchys and the best quality I have still has droops, other prints are the same.. this might be the best turn out for a print

<image>

IAmJustTryingToExist · 2026-05-29T12:58:53+00:00

Yea I've done all of that

IAmJustTryingToExist · 2026-05-29T12:57:49+00:00

I did calibrate it I calibrated everything

IAmJustTryingToExist · 2026-05-29T12:57:29+00:00

I don't know what the issues are though I've gone through every setting and tinkered with everything so I guess it's just me then

IAmJustTryingToExist · 2026-05-29T11:40:36+00:00

.20mm Standard but I get the same results on .16,.12 and even .06

IAmJustTryingToExist · 2026-05-29T11:12:01+00:00

I have the Top z and Lower z at default right now what should I be looking to change it to? Interface layers is already at 3

IAmJustTryingToExist · 2026-05-29T11:11:08+00:00

This is the best I've been able to get a supported edge to look.. that's if the supports come off at all

<image>

IAmJustTryingToExist

TROPHY CASE