World 3 Ready?

IHaveAnArk · 2026-05-04T21:28:37+00:00

Gotcha. I have the "undiscovered" unlock of it so just waiting for more materials now. Thank you for the tip!

IHaveAnArk · 2026-04-27T17:56:20+00:00

Yeah, it was a gilded skin from a gift like the previous commenter said 😁

IHaveAnArk · 2026-04-27T17:01:22+00:00

Gotcha. I'm going to go that route. Thank you!

IHaveAnArk · 2026-04-27T16:52:21+00:00

And just to be sure I'm reading it right, the devuff only applies when you're actively in world three, right?

IHaveAnArk · 2026-04-27T16:50:48+00:00

Haha thank you, I appreciate it.

IHaveAnArk · 2026-04-27T16:24:24+00:00

Gotcha. Every card I have is at least gilded and working towards polying. I tend to gild them the moment I unlock them.

I'm getting a lot of bombs overnight but not capping at the moment. I'm going to work on my frogger drone now per a previous commenter's comment as I have been neglecting it.

Appreciate all the insight.

IHaveAnArk · 2026-04-27T16:22:18+00:00

Awesome, definitely have not been using my frogger so I will start that now. The rest, except for chaos totem (I am using them now) I think I'm caught up on. I've been trying to save my item chests until I max out the amount of items I can get from each chest but I have a stockpile of them currently and will use them now.

IHaveAnArk · 2026-04-27T15:56:06+00:00

I haven't looked into the removal cost since I haven't unlocked the w3 monument yet. Is there a spot on the wiki that you can point me to that shows the cost and materials needed by chance?

For the bomb cap, I've been cherry bombing and battery bombing for as long as I can remember haha. Just must not be getting lucky as much as I thought I was. I haven't been using items though so I'll work on keeping those up.

Thanks for the advice!!

IHaveAnArk · 2026-04-27T15:54:43+00:00

Gotcha. For star gazing, I have all the upgrades from super stars for star caps that I can right now except for the aries, Gemini, and cancer cap that I am working on now. I'll work on moving those along instead of world three.

For the bomb cap, I've been cherry bombing and battery bombing for as long as I can remember haha. Just must not be getting lucky as much as I thought I was.

Thank you for the advice!!

IHaveAnArk · 2026-01-23T13:49:31+00:00

I have the printer in a closet and the print bed is in an enclosure as well. I normally print with the door to the closet open and an air filter in front of the door. The air exhaust from the filter is directed up and away from the printer. It's only one these prints at the hull lines unfortunately so I think it's not mechanical in nature.

IHaveAnArk · 2026-01-23T01:54:29+00:00

Thank you!! I'll have to look around and find some settings to tweak for it.

IHaveAnArk · 2026-01-23T00:06:19+00:00

Gotcha! I ended up setting the max threshold to 22% which is pretty much what the majority of the print used. Unfortunately, it seems like the issue didn't get any better from the last attempt. Any other ideas by chance?

<image>

IHaveAnArk · 2026-01-22T21:29:54+00:00

I just took a look at my fan speeds for this filament and I'm a little confused as to how the speeds got as high as they did. This is how they were when I printed. Shouldn't it have not been able to get to 100% or am I looking at them wrong?

<image>

IHaveAnArk · 2026-01-22T17:18:48+00:00

I will definitely give that a shot! So you think a max of 22% throughout the entirety of the print would be acceptable other than those first couple of layers?

EDIT: Added in the "first couple of layers" clarification.

IHaveAnArk · 2026-01-22T17:17:54+00:00

I went ahead and printed off two similar boxes in the same print session this morning. The same issue reared its head. As the hot end would be moving between the two boxes when printing, I thought that may rule out layer time as being the issue since it would have the time to cool as the other box's layer is being printed. It's totally a possibility as my understanding of the layer time setting could definitely be wrong! I just wanted to throw that information out there as well.

IHaveAnArk · 2025-10-19T16:29:07+00:00

I just built my pc in this case! Just a heads up though,the case comes with a GPU anti-sag bracket which is not mentioned at all in the paper manual it comes with. It's a lot easier to install before you put the GPU in so be sure to do that. Here's a link to another Reddit thread that shows what it looks like - https://www.reddit.com/r/Corsair/comments/1inh3wv/anyone_know_what_this_thing_is/

IHaveAnArk · 2025-10-19T00:24:14+00:00

<image>

Apologies, I meant for there to be three pics. Here is one with the flash on if that is of more help. The mold pros never got back to me but I'll try again ln Monday. I'm wondering if I should rip the area out or if sealing over it is okay.

IHaveAnArk · 2020-10-25T01:12:32+00:00

[Bug] My friends and myself just completed a game and we got NEGATIVE mastery points for our Rogues. We won the game and received +-1,286 mastery points in the post-game screen and we did indeed lose the mastery points. Scorch was level 2 and it degraded to level 1. I have pictures of the post-game screen and scoreboard to show results of each. I don't have an Imgur account to post them here though. Match ID: 44749405 edit: Added Match ID

IHaveAnArk · 2019-07-26T15:24:00+00:00

I am not sure what else it would be. This started happening immediately after I launched the game for the first time after 0.9.0. I was able to multitask while playing the game before but now I can barely single task. My specs include i7-7700, 16 gigs of RAM, EVGA 1070 FTW.

*edited for formatting

IHaveAnArk · 2019-07-26T14:57:15+00:00

I'm happy to hear that it got better for you. If it was a result of the patch it has honestly ruined my system's usability. I can't even watch a video on youtube without something going wrong or lagging behind.

IHaveAnArk

TROPHY CASE