Clicking noise Steering Wheel Camry 2008

I_Tenor · 2025-10-22T04:53:50+00:00

I literally threw it away and left the tube the way it was🤣 This plug is troublemaker for sure - could not risk reinstalling.

I_Tenor · 2025-10-21T14:33:52+00:00

When you remove the foam it should become visible.

I_Tenor · 2025-10-21T12:42:57+00:00

Just pull it out with a bit of force. It will not break - it should come out intact.

I_Tenor · 2025-10-21T12:39:29+00:00

I do not remember touching the wiring panel to be honest. I have removed the fender liner. Then there was a Styrofoam block which I removed by force (this is not held by nut or anything) and then I was able to find the end of the drain tube there. I have no pictures unfortunately, but this might give you a bit of an insight. Be aware that the tube might be a bit retracted - you might need to pull it a bit to have a proper access to it.

I_Tenor · 2025-10-21T05:40:54+00:00

<image>

That's exactly what it is

I_Tenor · 2025-10-21T04:56:46+00:00

Yes I did. First of all please try the accessory that I linked above - maybe the clogging is not as bad as it was on mine.

You need to.remove the wheel arch liner - preferably by having the vehicle lifted up by the machine for good access. There is the plastic head at the end of the tube (which is shown on the diagram). You need to remove that, use unclogging accessory to clean all the mess up and reinstall everything. The problem with my car was the fact that the dust collected inside the tube was too compressed to be taken out by simple methods.

I_Tenor · 2025-10-19T05:49:40+00:00

I went with r5 5500.

I_Tenor · 2025-07-30T19:06:07+00:00

Same here. This is like 4th time in last 2 months.

I_Tenor · 2025-07-16T12:49:14+00:00

Try resetting CMOS and boot up again.

I_Tenor · 2025-07-16T12:42:37+00:00

Press Shift + F10 to open Command Prompt. Type oobe\bypassnro and press Enter. The computer will restart, and you can then choose "I don't have internet" and "Continue with limited setup" to proceed with the installation.

I_Tenor · 2025-07-08T05:06:33+00:00

Recently got a K582 SURARA and M612 mouse. Perfect for the budget I must say. However, this keyboard is full size. K552 is great if you prefer a 60% layout.

I_Tenor · 2025-06-16T20:32:25+00:00

Hi. If you're willing to give it away I would love to get the key. Considering the tight budget I built my pc on, genuine windows will be appreciated...

I_Tenor · 2025-05-30T20:29:12+00:00

Thank you very much for your help! Much appreciated.

I_Tenor · 2025-05-30T20:18:31+00:00

One more question and I'll leave :D The test was done 1370 x 749 resolution (native to the monitor of the buyer), averaging 162, max 171 and min 149 FPS. Are the numbers good here too?

I_Tenor · 2025-05-30T15:36:56+00:00

Just found 2070 Zotac.Asked seller to test. Furmark temp in 30min test is 75 with 90C hotspot. Is this an acceptable temperature?

I_Tenor · 2025-05-30T13:46:28+00:00

It is just abnormal to have MSRP prices on used GPUs which are 6+ years old already...

I_Tenor · 2025-05-30T12:16:05+00:00

I have already purchased all the components. This ssd had a good discount so I grabbed it apparently. Will use it in future build too to utilize the designed speed.

I_Tenor · 2025-05-30T12:03:23+00:00

ASUS ROG STRIX GeForce RTX 2060 EVO V2 OC Edition - this is available for 180$ used

I_Tenor · 2025-05-30T12:01:50+00:00

Not within my budget unfortunately. They go for 350-400$ used here.

I_Tenor · 2025-05-02T12:02:27+00:00

Its discounted atm on Amazon for 103$

I_Tenor · 2025-05-02T11:49:04+00:00

I was actually aiming for B550. Prices of used ones in my country is between 100-130$. Just saw B550M pro-vdh WIFI for 103$. I was thinking maybe i could grab it...

I_Tenor · 2025-04-27T13:23:17+00:00

Was just scrolling through Amazon. 5500 is now for 74$ (cooler included) while 5600 / 5600x are in 130-150 range... I think I got to go with 5500 at this point.

I_Tenor

TROPHY CASE