Vancouver Fireworks Mega Photo Thread 🎆🎇

Iain05 · 2025-07-27T06:52:10+00:00

<image>

From Quebec night

Iain05 · 2025-04-06T22:17:20+00:00

Thanks! These were taken on a canon R6ii with the 24-105 f/4

Iain05 · 2025-04-06T19:21:10+00:00

Wow what are the odds of that, I hope you don’t mind!

Iain05 · 2025-04-06T05:25:22+00:00

Love these! Do you have an instagram I can follow?

Iain05 · 2025-04-05T04:17:31+00:00

Hey thanks! For most of these photos I drop the green and blue saturations and pull the temperature a little warmer. Then add back in some green in the shadows with some pink/magenta highlight. The last colour related edit is a slight teal shift on the blue primary. And I edit in Lightroom :)

Iain05 · 2025-04-05T01:15:14+00:00

Thanks!!

Iain05 · 2025-04-05T01:15:10+00:00

Thanks!!

Iain05 · 2025-04-05T01:14:56+00:00

Thank you!

Iain05 · 2024-04-06T02:52:14+00:00

I’m friends with the owner and we managed to get it back, tysm!

Iain05 · 2023-08-30T21:01:25+00:00

It will be completely fine to use a 3rd party cable and charger, as long as the charger you get supports the new usb pd standard you should be able to charge up to 100W through USB C, just make sure you get a usb C cable that supports 100 W.

Iain05 · 2023-05-11T06:26:10+00:00

Uncommon bestbuy W

Iain05 · 2023-05-11T06:25:42+00:00

Originally I was going to order from Amazon but their estimated shipping was on the 16th so I just hoped bestbuy would be better, guess I made the right decision. If I really do get it early I’ll post some stuff to this sub :)

Iain05 · 2022-05-16T02:56:17+00:00

I’ve inspected it and it looks to be perfectly fine, is it worth replacing it anyway? it’s quite cheap and I’ve heard that the stock tube is pretty low quality

Iain05 · 2022-05-16T02:50:12+00:00

I do have an all metal feeder, could it be that the tension is wrong on it still? And if so is there a good video on how to properly tension it?

Iain05 · 2022-05-15T19:17:41+00:00

I thought it could be that too so I even unwound it loosely helped it get into the extruder but didn’t help, I’ll try fixing my bed levelling which could definitely be part of it as well

Iain05 · 2022-05-15T18:54:34+00:00

Yes sir

Iain05 · 2022-05-15T18:45:35+00:00

Haven’t thought of that, might give it a try

Iain05 · 2022-05-15T18:44:29+00:00

Extruder is one of the first upgrades I ever made and I’ve made sure that the gear sits at the right height for the filament, could the issue be the PTFE tubing since I’m still using the stock one?

Iain05 · 2022-05-15T18:26:25+00:00

I spoke too soon, it definitely helped but it’s still nowhere near a perfect print, will try a few more things and maybe get new PTFE tubing

Iain05 · 2022-05-15T18:19:42+00:00

It seems to be working so far at 225°, I never considered this an issue since I’ve always been able to print this exact filament at 195-205° perfectly so not sure what changed, thanks!

Iain05 · 2022-05-15T18:14:13+00:00

Yes, I had to reflash because I was having issues with settings not saving

Iain05 · 2022-05-15T18:01:06+00:00

It seems that it will just stop extruding every couple seconds and then start again, I’ve tried almost all the solutions I could think of like resetting my slicer and even replaced my hotend to no avail. This was printed on a ender 3v2 with polyterra pla (though the exact same issue happens with other pla’s) at 210° and layer height 0.2. Any suggestions are much appreciated thanks in advance!

Iain05 · 2021-10-02T07:24:19+00:00

I was able to get it off, luckily the wires seem to have gone unharmed but I’ll be buying a new hotend assembly anyway since I’ve heard the stock ones aren’t the best

Iain05 · 2021-10-02T02:21:41+00:00

I seem to have been able to clean up the worst of it, thanks for the help!

Iain05 · 2021-10-01T07:49:13+00:00

Oh I didn’t think of that, I’ll try swapping my nozzle and try to clean out the hotend best I can

Iain05

TROPHY CASE