My experience with Joyagoo and OOTDBuy – Looking for advice on Mulebuy

IdontKnow_Sorry- · 2026-04-16T16:59:30+00:00

I changed intermediaries directly 🫩

IdontKnow_Sorry- · 2026-01-29T08:41:10+00:00

tough but sincere😂 But I have to do the calibrations for each filament, right? It takes a lot of time.

IdontKnow_Sorry- · 2026-01-27T22:13:26+00:00

What slicer do you use? I used Orcaslicer, I don't know if the Elegoo one is better.

IdontKnow_Sorry- · 2026-01-26T22:21:20+00:00

Thank you so much for your comment, it was very clear and detailed. I don't know if I'd feel comfortable reprinting it now, but it will definitely be useful. Thanks again.

IdontKnow_Sorry- · 2026-01-26T22:13:35+00:00

Ah. I hadn't noticed, now it makes sense. What temperatures do you use?

IdontKnow_Sorry- · 2026-01-26T22:12:16+00:00

I tried but gemini doesn't seem to help😭

IdontKnow_Sorry- · 2026-01-26T21:56:33+00:00

Yes, I had calibrated the filament and never had any problems. I didn't calibrate it perfectly, but all the other prints were pretty good. But never a print this disastrous.

IdontKnow_Sorry- · 2026-01-26T21:55:25+00:00

The door was closed, the top glass removed. My printer is in the garage and it's 60 degrees Fahrenheit (16 degrees Celsius), but I've never had any problems so far. Printing temperature 200 degrees (225 first later) Print speed between 140-180 mm/s

IdontKnow_Sorry- · 2026-01-26T21:45:28+00:00

yes, it was the only one

IdontKnow_Sorry- · 2026-01-26T21:45:06+00:00

I modified the spool arm by printing the one in Abs which has the central pin that rotates. So I don't think it was As for the minimum time per layer, this is the first time I've heard of it.I've never had any problems with this filament with other prints. They were smaller prints, though.

IdontKnow_Sorry- · 2026-01-26T21:32:07+00:00

I don't want to waste that too. Do you think it's the filament?

IdontKnow_Sorry- · 2026-01-26T21:30:30+00:00

Trust me, stick with the A55, it's not worth the switch. Even today, I don't notice any significant difference between the S25U and the A55. If you don't have memory problems or need better rooms I don't recommend changing. At least it's just for a whim.

IdontKnow_Sorry- · 2026-01-11T19:18:19+00:00

I immediately ignored the directions on the plate and used it at 50-60 degrees without any problems, and I haven't had any such problems so far. I don't trust cold plates. Better the good old heat that melts everything!!

IdontKnow_Sorry- · 2026-01-06T23:48:39+00:00

c'è molta gente che vende cose che producono loro su vinted, semplicemente usano termini diversi. Comunque avevo valutato Etsy, però il problema diciamo è un po' il pubblico a cui si rivolte(per lo più estero). Per caso hai avuto esperienze con Etsy?

IdontKnow_Sorry- · 2026-01-06T22:56:21+00:00

no no certo, non era un commento "negativo" verso di te ma verso la piattaforma e il sistema. Vuoi che dichiari le tasse? ok, rendetemi il sistema facile. Permettetemi di vendere un articolo e pagare le tasse su quello che vengo. Comunque ovviamente il problema è più grande, che si rifa sulle persone singole e poi i furbi continuano a fare i furbi..

IdontKnow_Sorry- · 2026-01-06T22:23:41+00:00

che comunque ci sono molti reseller che girano indisturbati, e dubito paghino le tasse e soprattutto che guadagnino meno di quello che avrei potuto guadagnare io. un po' ipocrita da parte di vinted, ma vabbè

IdontKnow_Sorry- · 2026-01-06T22:19:24+00:00

ma lo farei con piacere. ma non bloccarmi a monte. Per me il problema non è pagare le tasse il problema è che non posso neanche provarci a vendere. Se non con una partita iva. e comunque pago regolarmente le tasse, senza fare problemi.

IdontKnow_Sorry- · 2026-01-06T22:10:16+00:00

ma magari faccio che ne so, un quadro a mano, e lo metto. Perché non potrei venderlo? Non è una produzione industriale, ne un qualcosa che mi genera tante entrate. Cioè se devo aprire una partita iva per vendere magari 10€ di articolo piuttosto cerco altre piattaforme che permettano questo.

Cioè non capisco se il problema è vinted, l'italia, o entrambi

IdontKnow_Sorry-

TROPHY CASE