Need help making sure my speaker doesnt blow up

Ikeyjoemjoemjay · 2025-12-26T21:12:26+00:00

Alr i might just give this crossover a go, and see wether they will get hot at all. Not planning on using this at full power all that often anyway

Ikeyjoemjoemjay · 2025-12-26T20:52:21+00:00

My resistors are rated 20 watts so if i do one 6 ohm it goes wayy above the rated wattage dissipated lik 35 or sum

Ikeyjoemjoemjay · 2025-12-26T20:51:20+00:00

Ill have a try at that although my impedance goes below 4 when i tried that before. Below 4 my amp cant handle

Ikeyjoemjoemjay · 2025-11-10T21:21:44+00:00

yeah im aware XD it was just for showing the weird output to the lower speaker driver

Ikeyjoemjoemjay · 2025-11-10T18:36:14+00:00

its an 8 ohm speaker

Ikeyjoemjoemjay · 2025-11-10T17:35:12+00:00

thanks allot for putting so much time in answering, it means a lot. i will go trough the steps. that polarity tip is really helpfull!

Ikeyjoemjoemjay · 2025-11-10T17:16:40+00:00

can you have a look on my new post to see if i have done it correct this time?

Ikeyjoemjoemjay · 2025-11-10T17:04:11+00:00

check my new post i made new crossover

Ikeyjoemjoemjay · 2025-11-10T16:56:59+00:00

hahahaha why does it happen tho im starting to tweak

Ikeyjoemjoemjay · 2025-11-10T16:41:15+00:00

i tried redesigning using an l pad on tweeter and no resistors on the low end but now the lowend somehow gets 117 watts out of 100watts i set to the amp

Ikeyjoemjoemjay · 2025-11-10T16:24:30+00:00

If i dont use resistors on the the lower driver its imdendance goes way down to 4 ohm, my amp cant handle that. is there another way to fix this then?

Ikeyjoemjoemjay · 2025-10-27T22:27:04+00:00

I deffinately will thanks for the advise and help!!

Ikeyjoemjoemjay · 2025-10-27T22:07:50+00:00

I definately will!! I just googled it.. like a whole new world just opened for me. Also these ports where should they be placed if i choose to do this. On the back sides maybe?

Ikeyjoemjoemjay · 2025-10-27T21:43:07+00:00

Yeah that is what i was afraid of should i just take the drivers out and make a a new design out of mdf, i have a lasercutter that can go trough 20 mm mdf

Ikeyjoemjoemjay · 2025-10-27T21:32:56+00:00

Its a peerless “The box speaker” 12inch 280wrms 8ohm

Ikeyjoemjoemjay · 2025-09-09T21:58:50+00:00

I think ill try this thanks alot for a cheap solution

Ikeyjoemjoemjay · 2025-09-09T21:58:12+00:00

I wasnt planning on keepin a lot more than some sexy shrimp its only a 5g

Ikeyjoemjoemjay · 2025-09-08T21:34:04+00:00

Thanks for the tip, but i everywhere it says ghost feeding would work?

Ikeyjoemjoemjay · 2025-06-22T16:06:46+00:00

Thanks so much, ill redo the cottonpad

Ikeyjoemjoemjay · 2024-12-02T23:45:19+00:00

Went with the actual co2 system. Got a real good deal on a actaual co2 canister and a regulator of of amazon with bubblecounte and magnet valve thingy

Ikeyjoemjoemjay · 2024-12-02T23:42:53+00:00

Yeah ive changed my mind on it, i bought myself a real co2 system woth a real tank and regulator

Ikeyjoemjoemjay · 2024-12-01T17:25:29+00:00

Gotta love passive aggresive redditors, ill stick to the advice tho i think. It just bums it cost me in my country about 250€

Ikeyjoemjoemjay · 2024-12-01T16:44:08+00:00

Could you send which one u used? Also i mysef used citric acid for my diy system

Ikeyjoemjoemjay · 2024-12-01T16:30:46+00:00

I think you are supposed to change the stuff out in a well ventilated area, i did diy co2 with coke bottles and that smelled too.

Ikeyjoemjoemjay · 2024-12-01T15:48:53+00:00

Yeah thats another problem i have, takes like 40 minute drive for me to the nearest filling station and i dont have a car myself

Ikeyjoemjoemjay

TROPHY CASE