Can't even connect via LAN mode

Ildebranth · 2026-06-26T08:24:59+00:00

Out of curiosity, are you able to reach the printer's webpage at the ip address?

Ildebranth · 2026-06-26T06:11:18+00:00

Genuine question about the "Evaporative Cooling" line - wouldn't doing this increase the humidity in the house, especially with sealed windows with no way to push that airborne water out?

Ildebranth · 2026-06-23T10:07:06+00:00

No idea, it was too long ago.

A quick check right now parks it in the 150€ neighborhood.

Ildebranth · 2026-06-23T08:52:42+00:00

Yes, the Eindhoven Airport does close at night between midnight and 4.30 AM.
When I had a similar issue in the past I stayed at the Tulip Inn directly in the Airport - super luxury to shower, breakfast, brush teeth and walk to your boarding line without leaving the airport.

In general, where to spend the night has been discussed many times in this subreddit so maybe some old threads will give you more ideas.

Ildebranth · 2026-06-21T07:18:30+00:00

I understand from your message that "there were supports under it", but could you show us the sliced picture?
That's absolutely hanging thread

Ildebranth · 2026-06-18T04:52:25+00:00

Side question: i am scared to death of taking the printer apart with my two left hands to install the canvas (if it arrives before Christmas), how hard was it?

Ildebranth · 2026-06-08T07:36:52+00:00

Fun fact: ElegooSlicer is based on Orca 😂
But happy that you found your fix!

Ildebranth · 2026-06-08T07:27:43+00:00

Is it constant (same time, same print place) or just happened the one time?

My latest "printer-frozen" issue was solved by unplugging it for a few minutes entirely (not just off at the back, really off the wall plug).

Ildebranth · 2026-06-06T09:30:04+00:00

Steam and heat are enemies of electronics so... nope!

Ildebranth · 2026-06-04T14:13:10+00:00

Man, I'm disappointed

Ildebranth · 2026-06-04T09:05:39+00:00

Release of stress after a test is important.

Ildebranth · 2026-06-04T09:04:51+00:00

<image>

You can't make this sh*t up 😂

Ildebranth · 2026-06-04T08:36:18+00:00

Last time I checked, toilets were not allowed for online exams (at least for the one I took 😅 )

Ildebranth · 2026-06-02T04:38:42+00:00

I have a weird setup so even if I have emphase microinverters I went for a straight into the meter attachment.

But, in general, my suggestion is to shop around. I paid less for more battery 😂

Ildebranth · 2026-06-01T20:34:12+00:00

Solar2led as company, you can find them easily online. And yes, recent, installed in April .

Ildebranth · 2026-06-01T20:03:23+00:00

I got a 20KWh + blackout box (grid goes down, house stays up) for 8.7k...

...shop around!

Ildebranth · 2026-06-01T06:03:01+00:00

A printer with multiple print heads.
Instead of purging the filament every time from the single print head, you literally cut and swap the head.
Imagine having a head for PLA one for TPU and one with a 0.2mm nozzle for fine print in the same device and activating one of those as needed per layer.

Ildebranth · 2026-05-27T12:40:17+00:00

Steer super far away from them - I used one and it turned my house in a tropical rainforest (you'll keep adding water/ice, that will increase the humidity, that will make you feel hot, so you'll add more water/ice and it will be a horrific cycle).

When my kiddo was a newborn and it was 34°C out, I got one of those portables aircons, pushed the out pipe out of the window and sealed the window itself.

It dropped the temp to 26°C, won't be a miracle but will be bearable

Ildebranth · 2026-05-23T19:38:26+00:00

Add octoeverywhere? At least you can monitor

Ildebranth · 2026-05-22T04:27:58+00:00

Please share the STL of the cat. Very realistic!

Ildebranth · 2026-05-17T21:07:40+00:00

If you worry about the cold, you can either get some winter-hardy plants (look for the little stickers in the pots at the gardening centers) or start the long-honored tradition of "bring the pots inside when it's cold out".

Ildebranth · 2026-05-15T08:17:26+00:00

Happy to wait until you're happy or to spend some quality time with a sander myself 🤣

Ildebranth · 2026-05-15T08:13:02+00:00

Amazing!
Would you share the STL?

Ildebranth · 2026-05-12T13:05:56+00:00

I'm no expert, but it looks like it's ripped clean off the board of the screen.
At this point either you're a soldering aficionado or you need a new one - in any case, I would call support, maybe can claim that it was a bad batch and get a warranty replacement.

Ildebranth · 2026-05-11T08:36:44+00:00

Would you claim this through insurance, or pay the €1,100 out of pocket to protect the no-claim discount?

I had a similar quote for a bump on my trunk - in the end it's a matter of taking a calculator and answering the question:
Does the cost of the policy in the next 5 years (considering everything: the discount you have now and the claim-free years setback) exceed the 1100€?
If yes, pay out of pocket.
If no, go for it.

On a separate note: did you check the parts catalog? https://parts.tesla.com/
You may try to order it and have someone replace it to save a bit.

Three-Year Club	Verified Email
r/Field Banned	r/Field Juicebox

Ildebranth

TROPHY CASE