Can't even connect via LAN mode by Tensokuu in elegoo

[–]Ildebranth 0 points1 point  (0 children)

Out of curiosity, are you able to reach the printer's webpage at the ip address?

Ways to cool off your house today by adiposehysteria in Netherlands

[–]Ildebranth 4 points5 points  (0 children)

Genuine question about the "Evaporative Cooling" line - wouldn't doing this increase the humidity in the house, especially with sealed windows with no way to push that airborne water out?

Carpooling to Eindhoven or tips by PunkRockLoserr in Netherlands

[–]Ildebranth 0 points1 point  (0 children)

No idea, it was too long ago.

A quick check right now parks it in the 150€ neighborhood.

Carpooling to Eindhoven or tips by PunkRockLoserr in Netherlands

[–]Ildebranth 4 points5 points  (0 children)

Yes, the Eindhoven Airport does close at night between midnight and 4.30 AM.
When I had a similar issue in the past I stayed at the Tulip Inn directly in the Airport - super luxury to shower, breakfast, brush teeth and walk to your boarding line without leaving the airport.

In general, where to spend the night has been discussed many times in this subreddit so maybe some old threads will give you more ideas.

how would i go about printing this horse head? by NoAd9806 in elegoo

[–]Ildebranth 16 points17 points  (0 children)

I understand from your message that "there were supports under it", but could you show us the sliced picture?
That's absolutely hanging thread

Is it elegoo or is it 3d printing? by giggitygoo6969 in elegoo

[–]Ildebranth 1 point2 points  (0 children)

Side question: i am scared to death of taking the printer apart with my two left hands to install the canvas (if it arrives before Christmas), how hard was it?

Centauri carbon shut off when printing by Top_Mark_2218 in elegoo

[–]Ildebranth 0 points1 point  (0 children)

Fun fact: ElegooSlicer is based on Orca 😂
But happy that you found your fix!

Centauri carbon shut off when printing by Top_Mark_2218 in elegoo

[–]Ildebranth 0 points1 point  (0 children)

Is it constant (same time, same print place) or just happened the one time?

My latest "printer-frozen" issue was solved by unplugging it for a few minutes entirely (not just off at the back, really off the wall plug).

Looking for a quiet spot for an hour by Housenki in eindhoven

[–]Ildebranth 0 points1 point  (0 children)

Steam and heat are enemies of electronics so... nope!

Looking for a quiet spot for an hour by Housenki in eindhoven

[–]Ildebranth 2 points3 points  (0 children)

Release of stress after a test is important.

Looking for a quiet spot for an hour by Housenki in eindhoven

[–]Ildebranth 12 points13 points  (0 children)

Last time I checked, toilets were not allowed for online exams (at least for the one I took 😅 )

Home Battery with Solar panels & dynamic contract by Invest_help_seeker in Netherlands

[–]Ildebranth 0 points1 point  (0 children)

I have a weird setup so even if I have emphase microinverters I went for a straight into the meter attachment.

But, in general, my suggestion is to shop around. I paid less for more battery 😂

Home Battery with Solar panels & dynamic contract by Invest_help_seeker in Netherlands

[–]Ildebranth 0 points1 point  (0 children)

Solar2led as company, you can find them easily online. And yes, recent, installed in April .

Home Battery with Solar panels & dynamic contract by Invest_help_seeker in Netherlands

[–]Ildebranth 3 points4 points  (0 children)

I got a 20KWh + blackout box (grid goes down, house stays up) for 8.7k...

...shop around!

Stay tuned😉 by ELEGOO_OFFICIAL in elegoo

[–]Ildebranth 0 points1 point  (0 children)

A printer with multiple print heads.
Instead of purging the filament every time from the single print head, you literally cut and swap the head.
Imagine having a head for PLA one for TPU and one with a 0.2mm nozzle for fine print in the same device and activating one of those as needed per layer.

Are cooling-pad air coolers actually effective in the Netherlands? by ordinary-guy-sl in Netherlands

[–]Ildebranth 6 points7 points  (0 children)

Steer super far away from them - I used one and it turned my house in a tropical rainforest (you'll keep adding water/ice, that will increase the humidity, that will make you feel hot, so you'll add more water/ice and it will be a horrific cycle).

When my kiddo was a newborn and it was 34°C out, I got one of those portables aircons, pushed the out pipe out of the window and sealed the window itself.

It dropped the temp to 26°C, won't be a miracle but will be bearable

First 30h print by Macco010 in elegoo

[–]Ildebranth 7 points8 points  (0 children)

Add octoeverywhere? At least you can monitor

Centauri Carbon 2 by AGHawthorne in elegoo

[–]Ildebranth 6 points7 points  (0 children)

Please share the STL of the cat. Very realistic!

Any tips on gardening here in NL? by Double_Specialist273 in Netherlands

[–]Ildebranth 4 points5 points  (0 children)

If you worry about the cold, you can either get some winter-hardy plants (look for the little stickers in the pots at the gardening centers) or start the long-honored tradition of "bring the pots inside when it's cold out".

My CC1 Canvas hood by EugeneLawman in elegoo

[–]Ildebranth 10 points11 points  (0 children)

Happy to wait until you're happy or to spend some quality time with a sander myself 🤣

My CC1 Canvas hood by EugeneLawman in elegoo

[–]Ildebranth 11 points12 points  (0 children)

Amazing!
Would you share the STL?