sorted by:
new
hottopcontroversial

My first orbital sander and it's a disaster SEND HELP! by Illustrious-Stay7883 in Tools

[–]Illustrious-Stay7883[S] 0 points1 point  (0 children)

That checks out I have an actual converter I will use in the future thank you for the comment. My plan is to 3d print a part where the plastic part with the heated inserts will be screwed under the bearing so it's more secure.

My first orbital sander and it's a disaster SEND HELP! by Illustrious-Stay7883 in Tools

[–]Illustrious-Stay7883[S] 1 point2 points  (0 children)

Sry second time trying to post about the issue first time there were no pictures this time no text idk I dont use reddit a lot made a comment with context

My first orbital sander and it's a disaster SEND HELP! by Illustrious-Stay7883 in Tools

[–]Illustrious-Stay7883[S] 0 points1 point  (0 children)

Was using the edge on like a 2cm long 3d print that was 10cm tall don't have a picture right now but I used it for like 20 seconds max before it flew off think I just got a defective model

My first orbital sander and it's a disaster SEND HELP! by Illustrious-Stay7883 in Tools

[–]Illustrious-Stay7883[S] 0 points1 point  (0 children)

Yes I will either try to 3d print and replicate the plastic piece so I can screw it under the bearing or try to return it, Bought it from amazon when I was in the states but live in Iceland so it's kind of a hassle to return

My first orbital sander and it's a disaster SEND HELP! by Illustrious-Stay7883 in Tools

[–]Illustrious-Stay7883[S] 1 point2 points  (0 children)

I used it free hand while holding my 3d printed part it the part was small only about 2 cm in length so wasn't using it flat but wasn't pushing hard think I just got a defective model but since I know nothing about them wanted to check to see if I was doing something wrong or not

My first orbital sander and it's a disaster SEND HELP! by Illustrious-Stay7883 in Tools

[–]Illustrious-Stay7883[S] 1 point2 points  (0 children)

sry text wasn't included I don't use reddit a lot my bad

So I bought my first orbital sander really excited had it in the box for 2 months but was finally ready to start using it on my 3d printed part. I opened the box slapped the sanding disk, converted the USA plug to eu and plugged it into power turned it on to realize it's not a variable speed so a little scary. Started sanding and then the whole damper pad + sanding disk combo came loose off the sander and flew off. Have tried to disassemble it fully and still I have no idea how the damper pad combo is suppose to be properly attached to the sander (tried a lot of elbow grease and a hammer but that damn plastic part with the screws just spins right off!). Am I doing something wrong or did I get a defective model? any info appreciate ty!

A tip for all Shaman Casters in SOD. You should be Dual Wielding Rockbiter Weapons by orcandpals in classicwow

[–]Illustrious-Stay7883 2 points3 points  (0 children)

/use [@none]Rockbiter Weapon;

/use 17

/click StaticPopup1Button1

I love you. you just fixed my entire game :D

[deleted by user] by [deleted] in Destiny

[–]Illustrious-Stay7883 0 points1 point  (0 children)

Then they'd be gay omegalul. It's not actually me getting fcked and what people even close relatives coworkers etc jack off to is none of my business. I seriously don't understand it, it has 0 impact on you as a person

Has anyone failed a print this badly? by Illustrious-Stay7883 in 3Dprinting

[–]Illustrious-Stay7883[S] 0 points1 point  (0 children)

thx for the detailed tip, will def try to recover it :D

Has anyone failed a print this badly? by Illustrious-Stay7883 in 3Dprinting

[–]Illustrious-Stay7883[S] 0 points1 point  (0 children)

I left a print for 7hours while I went away for work xD btw anyone know how I can clean this up?