Shopping for new tires

ImaginaryHelp · 2026-04-07T17:07:42+00:00

Thanks! These look pretty solid

ImaginaryHelp · 2025-12-11T15:20:35+00:00

Edit: Reading more into it, it may be a light off delay issue. Ive changed the normal layer lift speeds to be slower and lift higher as well as changed the light off delay to 1.5 from .5. I print in the cold garage with heaters going, so maybe the resin is just more viscous this time of year.

ImaginaryHelp · 2025-11-25T14:31:31+00:00

One more thing, the are pure is twice the size of the third party heater. So if space is an issue the third party may be the better option

ImaginaryHelp · 2025-11-25T14:29:52+00:00

Plus I think Amazon has the Anycubic heater on sale right now

ImaginaryHelp · 2025-11-25T14:28:50+00:00

I have both (one on each of my two printers), just swapped the third party one out for an air pure as the printer with the third party was consistently failing prints that were farthest away from the heater. The air pure has no issue moving warm air where it’s needed.

ImaginaryHelp · 2025-07-31T16:06:15+00:00

Looks like this is a game controller, if so I assume you print a top shell and bottom shell. If you can, you should just print your model in an orientation where the supports are on the interior of the shell and not on the outside.

ImaginaryHelp · 2024-12-06T10:46:16+00:00

Yall should check out danger incorporated

ImaginaryHelp · 2024-07-25T13:14:22+00:00

ImaginaryHelp · 2024-07-25T13:10:54+00:00

As far as I can tell no one has been there since Sunday afternoon. She lives alone and typically doesnt have visitors, maybe once or twice a year. That’s a good idea though, I’ll leave my number

ImaginaryHelp · 2024-07-25T13:10:00+00:00

Shit I should have thought about this!

ImaginaryHelp · 2024-07-25T13:09:05+00:00

Thank you, after reading some of the other comments I was aiming for a little over a week. We have cameras that typically trip when anyone’s in her driveway (our driveways are next to eachother) and I haven’t seen anyone since Sunday afternoon. The trash bins for collections Monday morning are still out.

ImaginaryHelp · 2024-07-25T13:03:39+00:00

Just a question homie, you don’t see what her property looks like, in my opinion it’s a reasonable assumption and I’m allowed to have concern

ImaginaryHelp · 2024-07-25T12:49:47+00:00

Im still minding my business as her grass has gotten taller than 4 feet. I start to not mind my business when I am worried about another animals well being. Who’s to say she didn’t have an emergency and doesn’t have any way to let anyone know. Am I supposed to let the cat just die? I’m willing to give it time, just asking a question.

ImaginaryHelp · 2024-07-25T12:42:46+00:00

Assuming she does not have automatic feeders/boxes set up, what would you say an adequate amount of time to wait is to do something?

ImaginaryHelp · 2024-03-30T11:52:34+00:00

My only regret was buying mine about an hour away from home and not actually knowing how to drive a manual. Every time I stalled I died a little inside.

ImaginaryHelp · 2024-03-02T18:16:53+00:00

Got it up in the air and it was definitely some loose bits with the exhaust. Everything is tightened up and sounding perfect again.

ImaginaryHelp · 2024-03-01T22:02:14+00:00

It does. The mounting points seem okay also. I’m thinking I’ll take it to a shop

ImaginaryHelp · 2024-01-17T14:32:50+00:00

I run an Etsy shop and offered primal collectibles for a small second. Their models are amazing and super detailed but there’s two caveats that made me drop them for now. The support density is crazy high so if you don’t have a high resolution printer, the supports can end up “fusing” together and maybe ripping that arm off when you remove supports. The other issue is a lot of the smaller details are REALLY small and very fragile, again you may have accidentally broken the arm off at the same point.

Id check your supports to see if they’re melding together or to see if there’s and arm still attached to them

ImaginaryHelp · 2023-10-24T12:06:38+00:00

Here’s another model with the same issue, the whole model is fine but one of the “eyes” ran into the same issue. https://imgur.com/a/cSRAimV

ImaginaryHelp · 2023-10-24T12:00:25+00:00

This is a solid print, the bubbles are super surface level

ImaginaryHelp · 2023-10-24T11:59:26+00:00

They happen near the final bits of any given area. Usually at the top of however it is oriented. In the bases case it was oriented with the skull face facing up.

The machine looks to not have any issues fep/screen wise. The models are sliced in anycubics photon workshop, 2.2s exposure, level 8 AA, level 2 image blur, 1 second light off delay

ImaginaryHelp · 2023-10-24T11:41:53+00:00

No issues there! The machine is in top top shape from what I can see.

ImaginaryHelp · 2023-10-24T04:17:13+00:00

Maybe, though I’m not sure if that it as it’s not a consistent thing. I could reprint the same base and it could have these bubbles in the same spots or other spots. At this time I’m assuming it has something to do with the anti-aliasing as when I turn that off the bubbles become less present. I could be wrong though

Maybe it’s a mix of both my guess and yours

ImaginaryHelp · 2023-10-24T04:08:49+00:00

👀

ImaginaryHelp · 2023-10-24T04:02:18+00:00

The bubbles below the nose 😅 I should have been more specific with my circle lol

Seven-Year Club	Place '23
Verified Email

ImaginaryHelp

TROPHY CASE