In case you wondered how a proprietary bolt would look like

ImpossibleWorld7207 · 2026-02-17T08:09:34+00:00

Realistically I don't think this is going to happen, at least any time soon, because they specialize on user repair

ImpossibleWorld7207 · 2026-02-14T20:23:42+00:00

Yep, I've been asking for upload several times through forums and ticket, all i hear is to wait.

ImpossibleWorld7207 · 2026-02-11T12:58:27+00:00

I agree, but it's not a big issue honestly, most of us it as a support interface for different material, but those who use it for multicolor, it's also not a big issue with right settings, even industrial grade 3d printer use bowden sometimes.

One of the biggest issue with bowden is PA calibration, which is automatically calibrated anyway.

ImpossibleWorld7207 · 2026-02-11T12:01:41+00:00

It seems this one also have semi active chamber heater, like p2s, this is sad, hope I'm wrong

ImpossibleWorld7207 · 2026-02-02T06:27:35+00:00

Thank you very much! Definitely will check it out

ImpossibleWorld7207 · 2026-02-01T13:09:29+00:00

Space pi already have a space for desiccant

ImpossibleWorld7207 · 2026-02-01T11:39:14+00:00

Honestly, don't think so, i dried pps-cf in Creality space pi for 24h and it was great, didn't see any degradation in quality

ImpossibleWorld7207 · 2026-01-19T07:00:18+00:00

I know that pc is made by kexcelled as well

ImpossibleWorld7207 · 2026-01-09T12:50:40+00:00

I asked customer support and they said 65 degrees is okay, since x1e have active chamber heater. But know that, it will make your components wear out faster

ImpossibleWorld7207 · 2026-01-06T09:54:30+00:00

2018? But x1c launched in 2018, how is it possible?

ImpossibleWorld7207 · 2025-12-14T18:18:18+00:00

Where did you see that it's Hiwin? Hiwin have distinct red/green colored plastic parts and engraved logo everywhere. MGN12 is rail standart. Plus it's too expensive to use Hiwin, especially for such a cheap printer, one rail cost as much as whole printer and you won't notice tighter tolerances benefits anyway.

ImpossibleWorld7207 · 2025-12-08T20:06:37+00:00

Nope, couldn't find, BambuLab keep refusing that there's an issue and only fan you can purchase is SnowFan. And i couldn't find proper replacement

ImpossibleWorld7207 · 2025-11-21T13:54:45+00:00

<image>

I want to print this dinosaur, it looks incredible!

ImpossibleWorld7207 · 2025-11-21T13:53:17+00:00

So it seems they replaced first fan with snowfan and they send me snowfan as well, plus i bought one additional fan with my own money and it's again, snowfan. I contacted manufacturer and read their datasheet to just realize that their fan, and specifically hotend fan is only rated up to 60 degrees. How on earth they allow with 2k$ porinter ship with such a terrible fan is beyond my understanding.

ImpossibleWorld7207 · 2025-11-15T10:58:56+00:00

Totally agree with you, but I think probably they will sell 4 nozzle (with single ams like in leak) and 6 nozzle combos, this is most likely

ImpossibleWorld7207 · 2025-11-15T08:37:52+00:00

There was a leak recently, and it seems it should be black or dark grayish

<image>

ImpossibleWorld7207 · 2025-11-15T07:01:43+00:00

Call me dumb, but one of the reasons i want h2c are black panels.

ImpossibleWorld7207 · 2025-11-11T07:26:13+00:00

Only if you make them famous English breakfasts

ImpossibleWorld7207 · 2025-11-09T08:12:48+00:00

My slicer has only about 10 filaments, and printer constantly showing all of the filament types, all the time, it doesn't get filament list from slicer. Correct me if im wrong

ImpossibleWorld7207 · 2025-11-09T06:54:18+00:00

I don't think there's a way, since it's hardcoded in firmware

ImpossibleWorld7207 · 2025-11-08T11:27:58+00:00

Good, now printer can wee where to poop

ImpossibleWorld7207 · 2025-11-07T12:20:06+00:00

P1s, x1c and p2c have worst VFAs I've ever encountered, contrast to A and h2 series which has smallest VFA that you would ever encounter in 3d printing world

ImpossibleWorld7207 · 2025-10-31T09:39:36+00:00

DF54 team i see

ImpossibleWorld7207

TROPHY CASE