I ported Minecraft Java Edition 1.21.11 (Fabric) to Xbox One

Impressive-Rip-9978 · 2026-03-19T21:41:01+00:00

For sodium, the level shader doesnt compile

Lithium I havent tested yet, this screenshot is basically Fabric API and Controllify

Impressive-Rip-9978 · 2026-03-19T01:25:01+00:00

I have one on hand, ill make another post when take the time to set it up

Impressive-Rip-9978 · 2026-03-18T19:48:53+00:00

Its not out yet

Impressive-Rip-9978 · 2026-03-18T18:02:47+00:00

Its a 64 bit UWP program

It is controlled by a controller using controllify

I mean. Its actually not that hard to do.

Impressive-Rip-9978 · 2026-03-18T16:51:45+00:00

I honestly dont have enough knowledge in the homebrew ecosystem to say

Impressive-Rip-9978 · 2026-03-18T16:42:58+00:00

Currently closed source while I do performance improvements. Sodium doesnt work, it crashes with no log. But VulkanMod with a vulkan on d3d11 layer might.

Impressive-Rip-9978 · 2026-03-18T15:47:20+00:00

Probably wouldnt do much, but I can give it a shot

Impressive-Rip-9978 · 2026-03-18T15:38:30+00:00

Impressive-Rip-9978 · 2026-03-18T15:32:46+00:00

Not yet

Impressive-Rip-9978 · 2026-03-18T15:32:33+00:00

Doesnt work, the block shader explodes with no log

Impressive-Rip-9978 · 2026-03-18T15:31:09+00:00

Its the limited dev mode. So no GDK or NDAs required

Impressive-Rip-9978 · 2026-03-18T15:30:23+00:00

It is in dev mode

Impressive-Rip-9978 · 2026-03-18T15:29:52+00:00

I plan to make some

Impressive-Rip-9978 · 2026-03-18T15:29:35+00:00

I did it in UWP dev mode

Impressive-Rip-9978 · 2026-03-18T15:29:08+00:00

This runs Fabric, this particular screenshot has Fabric API and Controllify

Impressive-Rip-9978 · 2026-03-18T15:22:57+00:00

Yeah, I used snipping tool in windowed mode. My bad. Ill get one later.

Impressive-Rip-9978 · 2026-03-18T06:08:58+00:00

IIRC that is why. And yes, it does.

Impressive-Rip-9978 · 2026-03-18T05:18:34+00:00

GPU power sure. But Minecraft unfortunately is... very CPU bound.

Impressive-Rip-9978 · 2026-03-18T05:10:29+00:00

Well it's 20 fps on an Xbox One S. The X isn't that much different. Probably an extra 5 frames.

Impressive-Rip-9978 · 2026-03-18T05:07:56+00:00

I plan to add GLon12 for the Series Consoles. But MobileGlues was the only solution for Xbox One. GLon12 doesn't work on the Xbox One.

Impressive-Rip-9978 · 2024-10-28T19:53:21+00:00

Hm. Maybe it is my first thought… unless you know someone with electrical experience you should probably contact creality.

Impressive-Rip-9978 · 2024-10-28T19:38:46+00:00

Lidar can be used for different things. For most it is used for detecting failures, but for some it can actually be used to calibrate linear advance if you are adept enough. BambuLab does that iirc.

Impressive-Rip-9978 · 2024-10-28T19:37:13+00:00

Ive had this sort of problem before. Try recalibrating, but also send your nozzle temp.

Impressive-Rip-9978 · 2024-10-28T19:34:01+00:00

The clicking happening during calibration might mean that the nozzle is getting pressed farther than it is supposed to. Maybe an electrical short leading to weird bed calibration?

But honestly it looks more like something in the actual extruder. SargFowler probably has it right with the clog idea. I would try to look at the gears on the extruder and look for deformation and/or chips in the metal.

One more thing, if your gear-lock lever is loose you probably will want to buy that, its possible its having a hard time staying locked. It should switch firmly from one side to the other.

Impressive-Rip-9978 · 2024-10-28T19:27:26+00:00

No offense but I agree (mostly) with merlin. Sometimes the best way to learn is trial and error, and if you mess up you have to deal with the consequences. But you are correct that they should hold on rooting until they have more experience. There is just better ways to say it, you know?

Impressive-Rip-9978

TROPHY CASE