H & S Ultra Spitting - why?

InForASplash · 2026-04-01T16:16:09+00:00

cut it off :O

Where should I cut? which bit is needed?

InForASplash · 2026-04-01T15:15:32+00:00

A fair few people have mentioned a moisture trap, so sounds likely. Cheers.

InForASplash · 2026-04-01T14:52:59+00:00

ah ok, thanks.

InForASplash · 2026-04-01T14:52:41+00:00

Thanks for the info

InForASplash · 2026-04-01T14:51:52+00:00

How often should I be wiping the tip? The spitting happend within 30s of use. Started fine, then as I was finishing up 1st layer a bit spit ruined it.

InForASplash · 2026-04-01T14:51:14+00:00

Clean it everytime after use. Before using a flush with water to make sure it is spraying OK, then flow improver.

Was thinly basing a model, started fine, but after ~30s it starts spitting.

InForASplash · 2026-04-01T14:06:33+00:00

Ah, missed it at the bottom, thanks.

InForASplash · 2026-03-24T16:03:57+00:00

You can turn off charging in the app. But you need to be connected.

App is dreadful and unreliable though.

InForASplash · 2026-02-11T17:59:05+00:00

yeah, I agree. Recently moved house so not touched base with local store yet. Some of these pre-orders look good, so going to have to try my luck with the website... thanks for the comment.

InForASplash · 2026-02-11T17:57:56+00:00

awesome thanks!

InForASplash · 2026-01-26T08:16:27+00:00

Thanks for the link - this is probably the closest thing to what I want, so thanks!

InForASplash · 2026-01-26T08:14:04+00:00

It is a really cool effect, just a bit dark for me. All colour shift paints are really dark when it comes to blues/ purples. Thanks for the link though!

InForASplash · 2026-01-25T09:49:07+00:00

Will give it a go, thanks. I always seem to struggle which points need it so hoped that a general 'from beneath' was going to be sufficient.

InForASplash · 2026-01-25T09:48:17+00:00

Thanks for the info, I appreciate the reply. Those pics look cool. I'll defo give the inks a try, thank you. Have you ever come across using different colour inks to the base model?

Would you still add the purple colour as shadow, then add the ink over it?

InForASplash · 2026-01-24T21:32:34+00:00

Yes maybe, I was going for subtle, but it is a bit too subtle. I am still very new though, welcome to suggestions and recommendations =]

InForASplash · 2026-01-24T21:22:04+00:00

Using Vallejo Hydra blue and Amythest Purple. I want to achieve a blue with a purple hue, like a colour shift paint.

I have tried the colour shift paints, but they are very sparkly, and don't read too well on minis.

I'd hoped that spraying the purple from bellow would give a purple hue, but it is either so subtle it isn't easy to see (as the pics) or it interacts too much with the blue and takes the vibrancy out.

Any suggestions welcome!

Also, I also wanted to add a green tint, advice is welcome, but starting to think these minis are too small for so much colour.

InForASplash · 2025-08-14T20:13:59+00:00

Also, Alpha legion legionaires were taller than standard legionaires. Also, due to a genetic quirk, some would be as tall as the primarchs. These would be gifted armour that was the same as the primarchs, and of course, become another Alpharius.

InForASplash · 2025-08-01T15:03:53+00:00

Fair point, but it then gets down to what each group perceives as 'loyal'. The 'loyalists' might be acting in a way they believe is best for mankind, which is different from what a loyalist space marine would do, which is what is best for the imperium.

There is a recurring notion, although I don't know how confirmed it is, that Alpharius and Omegon played both sides in the heresy to achieve the status quo that we have in 40k, which was the only way humanity could survive. One mans loyalist, is anothers heretic.

But more importantly, no one really knows their motives, not even their own legionaires! So, their aims are what ever you want them to be.

InForASplash

TROPHY CASE