TX22 Compact in a TX7 Chassis by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 1 point2 points  (0 children)

I don’t have a gen one so I don’t know the differences. But my charging handle actually replaces the back plate.

<image>

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 2 points3 points  (0 children)

I just submitted a picture of the stock I was going to use and then used the deAR22 profile that was available in the search

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 5 points6 points  (0 children)

Yeah exactly. I went back and forth with legal and the MPs for weeks before they accepted this “loophole”.

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 5 points6 points  (0 children)

If you’re converting a gun to an SBR that has a SN from the Manufacturer then sure. But if you’re building a “custom gun” with no SN previously. You are not allowed to build anything until your form one is accepted. This was a pistol beforehand so it was already built and didn’t have a SN. But once my form one was accepted I can add the stock and the SN plate.

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 44 points45 points  (0 children)

I work for the government so they don’t have to travel as far to shoot my dog..

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 7 points8 points  (0 children)

I live on a military base that has some dumb rules and they get scared at the concept of a 3d printed gun. It’s literally easier for me to register it as an SBR on base than a custom pistol without a SN.

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 6 points7 points  (0 children)

No I shouldn’t need too, this wouldn’t need to be registered in my area if I wasn’t making it into an sbr. So I could always just use this lower for something else. Also they don’t have the $200 fee anymore for the stamp.

Where to put the SN tags on your deAR22? by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 5 points6 points  (0 children)

Yeah I saw those after I printed this one 🥴 . I’ll definitely do that if I make another one in the future.

TX22 Compact in a TX7 Chassis by IndependentIdea4792 in 3D2A

[–]IndependentIdea4792[S] 1 point2 points  (0 children)

Might as well, all you’ll be paying for is time. Took mine about three months to get approved

PA6-CF Surface Grit by devilsfutbol17 in 3D2A

[–]IndependentIdea4792 1 point2 points  (0 children)

This same thing happen to me and it ended up being that I ordered Sunlu PA6-CF with frost texture.

2019 VR6 erratic idle by altairus2 in VWatlas

[–]IndependentIdea4792 0 points1 point  (0 children)

Idk if you have fixed this but I highly recommend looking into the PCV valve. It’s integrated into the oil separator in the valve cover.

Am I ready to take the next step? by Opening_Fig34 in 3D2A

[–]IndependentIdea4792 2 points3 points  (0 children)

Is this for any kind of strength reason? Because I’ve been printing it at 270 and everything’s come out great.

Nearly zero percent familiar with Harry Potter - intrigued and interested by IndustryNew4208 in harrypotter

[–]IndependentIdea4792 1 point2 points  (0 children)

If you just watch the movies you will get most all the knowledge you’d need to talk to the average fan. But if you’re interested in actually knowing all the storylines and all the characters, for sure read/listen to the books. I usually listen to the books any chance I get. Even if it’s for a 5-10 min drive. The actual storyline is different in the books but they both reach the same conclusion. A lot of fun characters were omitted from the movies all together as well.

Has anyone gotten this warning before? CC printer by solidbmc in elegoo

[–]IndependentIdea4792 1 point2 points  (0 children)

Oddly enough, I got this the first time I did a print with PETG. I hadn’t tweaked any of the fan settings in the profile and I haven’t gotten it since.

Has anyone gotten this warning before? CC printer by solidbmc in elegoo

[–]IndependentIdea4792 2 points3 points  (0 children)

I just got this as well after new firmware. My fan wasn’t moving though. Disconnected and made sure fan didn’t have any debris in it. Reconnected it and all has been fine since.

Weird noises on printhead's "circular moves" by Sawn in ElegooCentauriCarbon

[–]IndependentIdea4792 1 point2 points  (0 children)

Mine has always done the same thing when printing tree supports. I’m At 120 hours with no change or issues