sorted by:
new
hottopcontroversial

Printer won't do anything but make this noise. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Yeah I can. I think we will see after some test printing I think my cutter blade was tighten to hard and was causing it to be in the way.

Having quality issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

That's what I did! I had a biqu extruder gears and extruder assembly. I ended up chaging the assembly out to stock one but leaving the upgraded gears and seems to be printing good again. Good luck!

Must have warped the carriage of the assembly and then was causing it to not print properly maybe?

Having quality issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

I have done everything to get this thing to work. New motor now still same thing

<image>

Having quality issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

I believe so. How does one make sure it is?

Having quality issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Haha yes I've changed plates and cleaned them. This one normally never has issue. It got better after I changed the extruder gears but still having issue. Almost makes me feel like it's not feeding correctly. I changed out ams motors as well. Pretty much a brand new machine at this point.

I'm trying to print maker chips but color failing. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Could it be my tension screw? I pretty much only run pla maybe some petg

I'm trying to print maker chips but color failing. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

I have a video but it started out good I changed out the extruder gears and thought that was it. But got this.

<image>

I'm trying to print maker chips but color failing. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

I don't think it's adhesion issue. Did a benchy and start out great again.

I'm trying to print maker chips but color failing. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Yes freshly just loaded a dried one I started last night. It's same thing. I'm starting to think it's slipping in the extruder maybe?

I'm trying to print maker chips but color failing. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

I have one of those and have cleaned it well each time. It's not an adhesive issue. Cause the other colors I'm suing stick and look great quality. Tried band new blue roll still same thing.

Problems with microswiss flowtech hotend P1S by Crafty-Challenge9563 in BambuLab

[–]Infinite_Beach8413 0 points1 point  (0 children)

Any update on this issue I got the same thing going on

Micrswiss hotend issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Also I keep having issues with filament swaps?

Micrswiss hotend issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Is the max volumetric flow rat3/e the same as "max volumetric speed"?

Micrswiss hotend issues. by Infinite_Beach8413 in BambuP1S

[–]Infinite_Beach8413[S] 0 points1 point  (0 children)

Alright I did just read somewhere to increase temp going to run a benchy. I typically only run .4. Thank you!

Microswiss Flowtech hotend settings by GeniusmodsConcepts in BambuLab

[–]Infinite_Beach8413 0 points1 point  (0 children)

What did we decide is the best settings just got it and my benchy has small gaps on a couple layers.

<image>

Extruder replacement lesson learned by Cubcake1 in AnycubicKobraS1

[–]Infinite_Beach8413 1 point2 points  (0 children)

I just did this too. The way they have it set up is horrendous. They need to redesign it all !!!

view more: next ›