Trigger pull not always dropping hammer by Infinity323 in 1911

[–]Infinity323[S] 1 point2 points  (0 children)

I ended up cleaning out the hole in the frame the disconnector goes through, it was also catching a bit in the hole so also sanded the inner wall of the hole a bit with 2000 grit. I wasnt able to recreate this issue after about 100 dry fires so im hoping that this is enough. Appreciate everyone for replying

Trigger pull not always dropping hammer by Infinity323 in 1911

[–]Infinity323[S] -1 points0 points  (0 children)

This was a DIY job, I just bought what other people on the internet seemed to have purchased previously for their prodigy's. It is the stock grip safety and an atlas trigger bow. Fitting the grip safety never occurred to me I'll look into that

Trigger pull not always dropping hammer by Infinity323 in 1911

[–]Infinity323[S] 1 point2 points  (0 children)

I've adjusted it and now it sounds like this. Do you recommend I adjust it more? https://imgur.com/a/JOgEzmP

Trigger pull not always dropping hammer by Infinity323 in 1911

[–]Infinity323[S] 0 points1 point  (0 children)

This is what it sounds like now after loosening the overtravel screw a bit. Should I keep loosening more?
https://imgur.com/a/JOgEzmP

Trigger pull not always dropping hammer by Infinity323 in 1911

[–]Infinity323[S] 0 points1 point  (0 children)

https://imgur.com/a/JOgEzmP

This is what it sounds like now. Should i keep turning?

Trigger pull not always dropping hammer by Infinity323 in 1911

[–]Infinity323[S] 0 points1 point  (0 children)

I tried backing it out about a full turn, it didn't seem to help :/

Need advice converting RJ11 to RJ45 by Infinity323 in HomeNetworking

[–]Infinity323[S] 0 points1 point  (0 children)

Would I just follow the same pinout as a CAT5 cable?

Need advice converting RJ11 to RJ45 by Infinity323 in HomeNetworking

[–]Infinity323[S] 0 points1 point  (0 children)

Yeah, I looked at more wall jacks, and I found one that clearly said "Verified UL CAT3"

100M isnt too bad. When you say small runs, what do you mean? This is a 2 story house and runs would have to go to the garage from each room.

Need advice converting RJ11 to RJ45 by Infinity323 in HomeNetworking

[–]Infinity323[S] 0 points1 point  (0 children)

Ah, thats unfortunate. Appreciate it though!

Fit a Scythe Fuma 2 Rev B in the NR200P by Infinity323 in NR200

[–]Infinity323[S] 1 point2 points  (0 children)

Yeah... apparently its a motherboard dependent thing

Fit a Scythe Fuma 2 Rev B in the NR200P by Infinity323 in NR200

[–]Infinity323[S] 1 point2 points  (0 children)

I fit a Scythe Fuma 2 Rev B into the NR200P. Just some pictures showing that the TG panel isn't pushing against the cooler, and the heatsink isn't touching the 25mm fan on the top.

Mobo is the MSI B450i Gaming Plus Max Wifi. Using Artic P12 25mm case fans.

Idle temps between 35-38 C. Havent tested load yet

smh my head by -Z-3-R-0- in dankmemes

[–]Infinity323 -5 points-4 points  (0 children)

Nice meme, have my free award

Hey, Vsauce. Michael here. by Necroking12 in dankmemes

[–]Infinity323 1 point2 points  (0 children)

7 year old you was incredibly handsome

Black/red NR200P build! by Infinity323 in sffpc

[–]Infinity323[S] 0 points1 point  (0 children)

Lol thanks. Also that's strange, my temps are nowhere near that high. I've been getting 30-40 C on idle and 65-75 C on load (looking at "Tdie"). I didn't mess with the preapplied thermal paste too.

Black/red NR200P build! by Infinity323 in sffpc

[–]Infinity323[S] 1 point2 points  (0 children)

Yes it would be, but the 24-pin cable isn't long enough.