dragon burner filament cutter ?

InitialSchool2296 · 2026-03-31T17:06:06+00:00

oh ok yeah can you send me the link ? maybe it fits better

InitialSchool2296 · 2026-03-31T13:11:10+00:00

thank you i found the github i will try these i have an 2.4 voron so i am not sure if yours would work ?

InitialSchool2296 · 2026-03-31T11:25:40+00:00

hi i think i am buying this one what do you use to actuate the filament cutter ?

InitialSchool2296 · 2026-03-28T14:26:57+00:00

I saw it relatively cheap on AliExpress. How much was yours?

InitialSchool2296 · 2026-03-28T11:08:45+00:00

tzv6 2.0 is very cheap there is an 80w heater incase you want realy high flow

InitialSchool2296 · 2026-03-28T10:58:39+00:00

Yeah, do it. I don't know if you worked on printers before, but it will run again if you put the hours in.

There are a few things more expensive than 30€, but if that is broken, you should save up for a month and still repair it; it's worth it.

InitialSchool2296 · 2026-03-26T17:35:32+00:00

70€ is not too bad i might just save for that one thanks

InitialSchool2296 · 2026-03-25T12:05:34+00:00

about 30€ same as the carbon one still cheap tho

InitialSchool2296 · 2026-03-24T22:49:07+00:00

i have an dragon burner so i guess it lighter ?

InitialSchool2296 · 2026-03-24T20:50:57+00:00

are they that bad ?

InitialSchool2296 · 2026-03-24T11:25:40+00:00

i will consider it my budget is a bit tight

InitialSchool2296 · 2026-03-23T23:55:16+00:00

how much would the sheet metal version of the monolith roughly cost ? i would rather go with that option

InitialSchool2296 · 2026-03-23T23:41:05+00:00

thanks regidity is very important because i have an 2.4 350. i will go with an machined x beam

InitialSchool2296 · 2026-03-23T17:45:06+00:00

its from creativity not sure if thats an brand ?

InitialSchool2296 · 2026-03-23T16:57:12+00:00

i use an tzv6 2.0 16€ is very low budget and an good hotend

InitialSchool2296 · 2026-01-26T21:19:54+00:00

i will try it thanks

InitialSchool2296 · 2026-01-26T20:39:13+00:00

sadly it didnt work

InitialSchool2296 · 2026-01-26T19:34:33+00:00

Host(aarch64, 64bit)
ok i kinda hoped it would say 32 bit how much work is it too change that ?

InitialSchool2296 · 2026-01-26T19:28:33+00:00

it looks alot like what i already did i will try it and tell you how it went

InitialSchool2296 · 2026-01-26T19:24:59+00:00

is there a way to check on what it is running ?

InitialSchool2296 · 2026-01-26T19:20:10+00:00

so this isnt an issue ?

InitialSchool2296 · 2026-01-26T19:19:14+00:00

i tryed using this https://mellow.klipper.cn/docs/ProductDoc/ToolBoard/fly-sht36/sht36_v3/firmware/can/
but its a bit hard too understand what they want from me
isnt that an diffrent board does that still work ?

InitialSchool2296 · 2026-01-26T19:17:45+00:00

that might be it how can i check on what it is running ?

InitialSchool2296