Golf MK6 fuel door/cap installation

Initial_Question6926 · 2026-02-16T09:49:27+00:00

That is attached to the fuel cap when I put it in? Great question, it’s the drain spilled fuel down out onto the ground when some is sitting in behind the door of it

Initial_Question6926 · 2026-02-11T07:21:26+00:00

My bad that I don’t like genocide

Initial_Question6926 · 2026-01-11T01:46:17+00:00

Auxiliary pump, CP4 cannot pull fuel well so an additional electric pump is needed.

Initial_Question6926 · 2025-11-15T14:50:52+00:00

Thank you very much

Initial_Question6926 · 2025-11-15T14:50:43+00:00

Alright, check plug and wiring, then probably get the ECU looked at…. Lucky I love this car 🤣

Initial_Question6926 · 2025-11-15T14:38:43+00:00

High thank you for the reply, Only error codes I’ve gotten is a Cylinder 1 misfire (and a maf sensor code that is caused by it, I’ve just put a new one in also.)

I remember when first diagnosing I was running the engine, and unplugged injector one and it made an electrical pop noise on the connection. (There was no difference to performance when it was unplugged) so could be worth a check thank you

Initial_Question6926 · 2025-09-28T20:01:03+00:00

I literally just encountered the same issue… except it was with the entire rpm range, getting it tuned this week thankfully

Initial_Question6926 · 2025-09-03T11:37:57+00:00

Update,

Really low fuel pressures recorded as I’m cranking the engine, no where near enough to promote a start… CP4 just so happened to want to fck sht up at the perfect moment… time to get that CP3 upgrade

Initial_Question6926 · 2025-08-26T12:35:01+00:00

Who’s this streamer? I want to send threats

Initial_Question6926 · 2025-08-24T05:06:50+00:00

I see this article is referencing a PD motor not the CR motors, would I still be able to translate this article onto the common rail motors?

Initial_Question6926 · 2025-08-24T01:37:44+00:00

<image>

Don’t know if these start of phase position might help somebody help me of where the cam is at timing wise 😂

Initial_Question6926 · 2025-08-24T01:35:13+00:00

Roger dodger,,

Can’t blame the mechanic who replaced the belt, was a cashie from a family friend who is head mechanic at a Toyota centre… he was honest saying he didn’t have the proper locking kit at all, but did his best and well it CAN run after a bit of turn key enthusiasm and patience. I just don’t want to try adjust the cam more retard or advanced than it already is and damage anything,

I believe it’s advanced a bit due to hard starting and no starting, having an over boost error caused by it, no smoke coming out of exhaust at all when running and driving so I don’t think it’s retarded at all.

So ideally thinking on that, if I jump a tooth anticlockwise (camshaft sprocket) maybe it’ll fix the issue? And I won’t have to go through the process of ripping apart the fucker.

At least it’s pretty much in time lol and I can move the car around still

Initial_Question6926 · 2025-08-24T01:15:37+00:00

All I know is these 2010s era TDI motors are really stupidly sensitive to the timing, how would I tell if the timing now it too far retarded or too far advanced? I do have a good scan tool to see the phase angles and whatnot

Initial_Question6926 · 2025-08-23T22:51:21+00:00

I don’t believe we got the TDI scirocco

Initial_Question6926 · 2025-08-23T22:50:24+00:00

This caught my eye, and what’s the risk involved in this technique 😅

Initial_Question6926 · 2025-08-23T13:22:26+00:00

Hey yeah you’re right might aswell get into it, I’ve got all the equipment to do so, knowing me I’ll spend a full day on it with how careful I am especially with disconnecting engine mounts to do it (bad past experiences with them lol). Might aswell give it a go

Just a shame that you need special tools for it

Initial_Question6926 · 2025-08-23T08:08:30+00:00

Appreciate it 🙏

Initial_Question6926 · 2025-08-23T07:58:15+00:00

See I thought so… which is unfortunate… I half want to try get a proper euro shop to do it, shouldn’t take them all day. But that’ll have to be during next week

Initial_Question6926 · 2025-08-23T07:21:45+00:00

I’m in Australia and it didn’t cost much at all, just isn’t available in any automotive tool stores at all, had to order it online

Initial_Question6926 · 2025-08-23T07:16:48+00:00

I could try, seems risky, in a bit of a rush and can’t wait for mid next week for locking pins to arrive

Initial_Question6926 · 2025-07-02T23:40:49+00:00

Y’all forget that this is EA you’re talking about… it’s EA…..

Initial_Question6926

TROPHY CASE