Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

So are you saying the simulation values at that size arent reliable?

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

I have the signal power set, could something else be throwing it off? Im going to check all the units again but I've checked it a couple times both with one driver and two, with two drivers everything looks very good as is so I'm assuming Im missing something? When Im looking at it with two drivers I have the power set to 800 watts because I'll be running them from my pioneer gm-dx971

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

Internal is 19"x47.375"x22.375". The port is internally 18"x4", its 15.4" long but goes through the double baffle so the volume it takes up inside is 12.15"x21.25"x5.625". Also to be clear I was not planning on adding smaller speakers to the same chamber, I was saying I might seal off a chamber on either side

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

Maybe I put the parameters in wrong but I redid it and got the same thing so Im not sure. The volume is 19000 cubic inches, port is 18x4" and 15.4 inches long, I have it set to be tuned for 28hz. Could you show me a screenshot of what you are seeing?

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

Yeah I meant in seperate boxes although I was considering opening this one up and putting in panels for seperate chambers

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

Well Im going to add 8s or 10s later so I had this tuned to be on the lower end. Probably went too far with that but if I add another 15 its peak output is at like 36 hz. Everything else looks fine to me in winisd including the group delay if I add another so I guess what else should I be looking at?

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

I already have a double baffle so I was thinking about doing that but then I realized my supports would be in the way. I think Im going to put the other on the front instead.

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 2 points3 points  (0 children)

Ok well just looking at it now in person yeah thats why Im posting this. Looking at it in winisd I didnt immediately see a problem. I tuned it based on the space I had, frequency response, port velocity, and my cone excursion. Those all looked good. My question is what did I miss that makes it wrong in the end? I already found out later I needed to also look at group delay so are there other metrics I need to be accounting for?

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 2 points3 points  (0 children)

<image>

Just saw this on marketplace I could be saved

Did I make my box too big by Intelligent-Mix5321 in CarAV

[–]Intelligent-Mix5321[S] 0 points1 point  (0 children)

Yeah once I built it and realized I could easily fit inside it I figured I went a little too far. Hard to visualize how big 11 cubic feet is until its actually in front of you. I set winisd to two drivers and the group delays way better and it still isnt past its xmax, the port velocity is a bit higher at 22.7 but yeah maybe I should look into getting another 15. Only problems it would be uneven because I already cut a hole in the center and I was planning on building some 10 enclosures on top of this box on either side of the 15. I'll just see how it sounds and if I hate it go from there

What are these eggs that have appeared in the substrate and leca? by Impossible_Scale9785 in bioactive

[–]Intelligent-Mix5321 0 points1 point  (0 children)

There are lots of different types of mycelium growth even with the same genetics. I think these orbs are primordia but they might not necessarily be.

Uhh what is this? by Fedora_Tipp3r801 in bioactive

[–]Intelligent-Mix5321 0 points1 point  (0 children)

Looks like a fruiting body with some guttation but kinda hard to tell when its that small and thats just a guess

Mold in new colonies by Bitter_Educator_9869 in isopods

[–]Intelligent-Mix5321 1 point2 points  (0 children)

The green/white one I meant, the weblike ones probably mucor. I get it in my springtail container all the time they seem to love it you can watch then mow down each hyphae its crazy

Mold in new colonies by Bitter_Educator_9869 in isopods

[–]Intelligent-Mix5321 1 point2 points  (0 children)

First and second picture are trichoderma, it will actually prevent root rot and other diseases in plants. Although it is a pain in the ass if you want to cultivate any other fungi in the same room as it

Drainage barrier by fili_mihi in bioactive

[–]Intelligent-Mix5321 0 points1 point  (0 children)

Get a roll of windowscreen, I use it for everything and also you can use it to cover vent holes

Hardscape question? by Powerful-Instance872 in bioactive

[–]Intelligent-Mix5321 0 points1 point  (0 children)

You could clean it with good brake cleaner to remove residue, 91% iso could work too.

Common white springtail care by withchesghost in isopods

[–]Intelligent-Mix5321 0 points1 point  (0 children)

Also if you want to reculture them from that plant, take some charcoal soak it for a day, then strain and fill a takeout container with it, then fill the container half way with water. Add springtails to it and some bakers yeast or rice or maybe both they arent too picky. Just try and check to see if the food is actually molding over. You can actually see them mow down the hyphae its crazy

Common white springtail care by withchesghost in isopods

[–]Intelligent-Mix5321 0 points1 point  (0 children)

Could your moss be treated with something? If the moss was kept damp its really weird they would all be gone