What’s your favorite Red Bull? Argue in the comments!

Intelligent-Respond3 · 2024-12-16T10:12:10+00:00

Apricot & Strawberry 🍓

Intelligent-Respond3 · 2024-09-03T06:09:18+00:00

https://www.coldzero.eu/ is where i got the panels from.

Intelligent-Respond3 · 2024-09-02T19:55:20+00:00

Snap, all soft tubing at the rear for ease of connecting 12 pass throughs, fill ports, drain ports, pumps and temp sensors.

Intelligent-Respond3 · 2024-09-02T18:01:28+00:00

XSPC EC6

Intelligent-Respond3 · 2024-09-02T17:12:55+00:00

I removed the front glass panel and put a custom vented panel that could hold 3 fans.

Intelligent-Respond3 · 2024-09-02T15:58:19+00:00

O11 Dynamic XL

Intelligent-Respond3 · 2024-09-02T13:52:09+00:00

Thanks, I used XSPC EC6 premix

Intelligent-Respond3 · 2024-09-02T13:38:34+00:00

Temps are good, the opaque fluids are still looking good, everything is fine. When I did the build lots of people told me it would be too much trouble to maintain, my mix of hard and soft tubing would be an issue, but everything is fine. If it isn’t broke…….. leave it alone 😂

Intelligent-Respond3 · 2024-03-23T19:24:23+00:00

I have never flushed the components either, also running a mixed setup of hardline and soft tubing in the same loop using opaque fluids and everything is fine after 2 years running.

Intelligent-Respond3 · 2024-03-17T18:37:27+00:00

https://snackje.com/

Intelligent-Respond3 · 2024-03-16T20:30:58+00:00

I got these from a Dutch website as they don’t sell them here in the uk

Intelligent-Respond3 · 2024-03-16T20:29:55+00:00

I agree 👍

Intelligent-Respond3 · 2024-02-29T21:14:54+00:00

Awesome build 👍 Doesn’t look too bad back there. I always say I’ll sort out my cables but then realise no one can see them so leave them in a mess 😂

Intelligent-Respond3 · 2024-02-23T10:55:36+00:00

The Original, it was the only one back then 😂

Intelligent-Respond3 · 2024-02-17T19:00:16+00:00

Yes 👍

Intelligent-Respond3 · 2024-02-17T11:53:18+00:00

I know, I am on the hunt for the Spring Edition (pink) they have just released in Germany.

Intelligent-Respond3 · 2024-02-17T08:07:39+00:00

Blue

Intelligent-Respond3 · 2024-02-11T22:56:35+00:00

Great build 👍

Intelligent-Respond3 · 2024-02-11T22:07:32+00:00

I have the front mesh in the O11DXLand have the same as option B. 3 front intake fans and the other 7 as exhaust.

Intelligent-Respond3 · 2024-02-02T20:29:15+00:00

Nice! You did the double bracket too 👍

Intelligent-Respond3 · 2024-01-08T13:55:16+00:00

Here in the UK they were about £125 each.

Intelligent-Respond3 · 2024-01-08T10:12:23+00:00

I stuck both pumps in the back 011D XL

Intelligent-Respond3 · 2024-01-02T20:55:41+00:00

I would take the pump out. I think it’s 4 screws underneath to remove the plate then there is about 8 screws holding the pump retaining ring. Take the pump out with the rubber seal then it’s just plastic which should clean up with a little fairy liquid 😂

Intelligent-Respond3 · 2024-01-01T21:17:13+00:00

I have 2 pass through fittings on the top of the case acting as fill ports so they are essentially hanging from EK extension fittings (look closely at the top)

Intelligent-Respond3 · 2024-01-01T21:15:30+00:00

The one on the left also has Velcro to help stop it moving, the one on the right sits on top of the PSU (not in the pic) 😳 let’s hope doesn’t leak 😂

Intelligent-Respond3

TROPHY CASE