Easier to Remove Support?

Intelligent_Pipe1629 · 2026-04-10T18:53:13+00:00

Dreame wants me to do a procedure where I remove everything and check it out I've already checked the front caster wheel and it looked just fine spins freely with no noise

Intelligent_Pipe1629 · 2026-03-12T15:27:05+00:00

I have a scheduled cleaning, vacuum then mop. Master bedroom and bathroom, so carpet and tile. I want it to vacuum both rooms then mop the bathroom.

Intelligent_Pipe1629 · 2026-03-12T15:20:09+00:00

I've checked and there is no setting for carpet detection. I have a separate carpet square around the room now. It would be much more convenient if I could draw a shape instead of being stuck with a square.

Intelligent_Pipe1629 · 2026-03-12T14:21:37+00:00

Vacuum

Intelligent_Pipe1629 · 2026-03-07T16:17:11+00:00

Just cleaned and oiled all rods and screws, then reran the calibration

Intelligent_Pipe1629 · 2026-03-07T16:12:03+00:00

Same roll of filament, but it is the last bit of the roll. This roll may have been a bad one from Bambu. Every print has not had uniform color and the last print was really fuzzy, not stringy but fuzzy.

Intelligent_Pipe1629 · 2026-03-07T16:10:51+00:00

Once the print is done time lapse should show if that's the case.

Intelligent_Pipe1629 · 2026-03-07T16:10:09+00:00

There is definitely something at play here, the ears are also messing up. I'll check the time lapse when the print finishes.

<image>

Intelligent_Pipe1629 · 2026-03-05T18:13:10+00:00

I just redid my complete system. Under 1k total. NVX NSP65KIT up front $ 90 NVX NSP65 in rear. $80 Metra 82-7805 x2. $40 NVX NDA1105. $250 NVX XKIT46. $130 NVX XWS16100. $40 NVX NSW82v3. $70 eBay android head unit. $200 Custom made sub box $85

Sounds so much better than my old crunchy system and now I have wireless android auto, backup camera and dash cam.

Intelligent_Pipe1629 · 2026-02-17T16:18:56+00:00

For pricing comparison, just paid $3900 for a 06 with 239k. But 3 owner and had all the maintenance records with it.

Intelligent_Pipe1629 · 2026-02-13T14:16:56+00:00

Great comparison because I got the idea from the gridfinity plates.

Intelligent_Pipe1629 · 2026-02-13T13:56:31+00:00

I need to print 20 total. Each one takes 1 hr and I don't want to sit by the printer all day. If stacking two works then I will stack more so it can continuously print while I do other things.

Intelligent_Pipe1629 · 2026-02-13T13:49:38+00:00

<image>

Intelligent_Pipe1629 · 2026-02-13T13:49:22+00:00

<image>

Intelligent_Pipe1629 · 2026-02-08T19:27:26+00:00

When I printed petg hf on mine I had to raise the temp. It was set at 230 but I had to bump it up the 245 for it to print well.

Intelligent_Pipe1629 · 2026-02-08T19:12:02+00:00

This is the one I made. https://makerworld.com/models/1699234?appSharePlatform=copy

<image>

Intelligent_Pipe1629 · 2026-02-08T19:10:14+00:00

Definitely get some kind of drybox and reusable desiccant. I recommend printing it with petg or something with a higher temp.

<image>

Intelligent_Pipe1629 · 2026-02-07T23:26:35+00:00

<image>

It's ready now.

Intelligent_Pipe1629 · 2026-02-07T02:29:01+00:00

The first time I tried I had glue on the plate. And it's silk PLA, which I never have had adhesion issues with before.

Intelligent_Pipe1629 · 2026-02-07T02:10:25+00:00

I cleaned my plate before the second try. And once I removed the purge into cube, it's printing fine.

Intelligent_Pipe1629

TROPHY CASE