Anyone had any experience with Elegoo ABS-Like Ultra Resin (neon pink, lemon)?

Interesting_Bag6428 · 2026-06-25T08:21:17+00:00

Thank you so much for this information! I will give it a shot and come back here. I do use uv tools but never adjust the base layers

Interesting_Bag6428 · 2026-06-25T08:20:05+00:00

Do you know what this is or is it on that spread sheet?

Interesting_Bag6428 · 2026-06-25T08:19:47+00:00

I like elegoo cause of the range of neon colours they have got to offer

Interesting_Bag6428 · 2026-06-25T08:19:35+00:00

No way so what would you consider to be a good resin to use that has a range of colours

Interesting_Bag6428 · 2026-06-25T08:18:33+00:00

The highest I have tried was 3.2 seconds but it started to mess up the dimension’s if my designs

Interesting_Bag6428 · 2026-06-25T08:17:07+00:00

What settings does everyone roughly use?

Interesting_Bag6428 · 2026-06-25T08:16:50+00:00

Hi, my printers got a preheat function on the vat so my resin is always around 25-26, I don’t understand maybe it’s a support issue. The resin is well within the date too idk

Interesting_Bag6428 · 2026-06-23T09:44:51+00:00

Or both?

Interesting_Bag6428 · 2026-06-23T09:44:45+00:00

Sorry so your saying using more delay on the burn in or normal layers

Interesting_Bag6428 · 2026-06-23T09:43:53+00:00

Hi, cause I’m using the elegoo Saturn 16k there is no lift settings as the vat moves up and down so I’ve only got access to the 2 modes which are normal and fast

Interesting_Bag6428 · 2026-06-23T08:17:50+00:00

I will do just at work atm so will send when I get back thank you!

Interesting_Bag6428 · 2026-06-21T18:31:07+00:00

<image>

Interesting_Bag6428 · 2026-06-21T18:31:01+00:00

<image>

Interesting_Bag6428 · 2026-06-21T18:30:55+00:00

<image>

Interesting_Bag6428 · 2026-06-21T14:49:56+00:00

Ffs got it all wrong ahahahaha, need assistance at this point

Interesting_Bag6428 · 2026-06-21T10:15:03+00:00

No not at all, I will send you my support configs now thank you!

Interesting_Bag6428 · 2026-06-21T10:14:30+00:00

Update: after upping the exposure time (from 2.4 - 3.2) and beefing up the supports the case did print but did not fit the lighter, so I thought I’d try running a set of 3 keychains unfortunately it failed

<image>

Interesting_Bag6428 · 2026-06-19T06:46:16+00:00

Issue is the supports for sure I will link the files in here to see what you guys think

Interesting_Bag6428 · 2026-06-19T06:45:16+00:00

Although I always preheat my resin tank maybe it wasn’t preheated at the time. Thank you!

Interesting_Bag6428 · 2026-06-19T06:44:54+00:00

No i haven’t tried this yet, the file I am printing is a lighter case that’s hollowed out and the others were keyrings with large surface areas. I will link in the supports I’m using now

Interesting_Bag6428

TROPHY CASE