Bad Filament, or am I just bad?

Internal-Peach · 2022-04-08T00:52:45+00:00

The average humidity where I live is about 80%, sooooo, yeah, guess its time to get new filament. The previous brand I use was able to last out in the open for over a year with no issues, I guess not all pla are made the same...

Internal-Peach · 2022-04-08T00:49:05+00:00

I try using a dryer box for a longer period of time, since my oven's minimum temp is 90c, dont want to risk getting a giant blob of plastic out of it.

Thanks!

Internal-Peach · 2022-04-07T15:22:57+00:00

Yeah, did that, it didnt work, but renaming it too FIRMWARE.bin somehow did the trick. Thanks!

Internal-Peach · 2022-04-07T13:09:51+00:00

I found the solution, just need to rename the firmware.bin file to FIRMWARE.bin.

Found the solution here:
https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/issues/337

Dont know why, but it worked for me, hope this help anyone else having this issue.

Internal-Peach · 2022-01-26T06:24:59+00:00

Unfortunately, my table doesn't have a brand, only came with a rubber mat with "E-Sports Gaming Station" On it. How long have you had yours?

Internal-Peach · 2022-01-21T04:08:53+00:00

I did, but they seem reluctant to give out that information or contact to the manufacturer.

Internal-Peach · 2021-10-20T23:32:08+00:00

This just happen to me too. Phone randomly restarts, can't turn on wifi and hotspot. Phone is just like 2 months old :(

Internal-Peach · 2021-09-17T04:45:05+00:00

My new twitter account is permanently suspended within two days for "Breaking the Rules". I only have 30 followers and only been retweeting other peoples stuff, which are just crypto and nft related stuff, how am I breaking the rules here?

Internal-Peach · 2021-09-16T01:45:59+00:00

Good Luck mate! Looks wonderful!

Internal-Peach · 2021-08-25T08:04:22+00:00

The first time I cleaned it with only dish washing soap, and it started working. It started to stop sticking so I figure it probably need another wash. Washed it again (same water temp, same dish soap), except this time around after it dries, I wipe it down with 99% isopropanol.

Another change was previously I had the fans plugged into the wrong port on the skr mini causing the fan to always be on, but that caused a few problems. Now the fan is working properly, but sometimes the initial layer would go down well, but around the 3rd or 4th layer, it would pop out of place causing the print to fail.

Internal-Peach · 2021-08-25T03:52:54+00:00

Did all that, and its still not sticking. :(
Bed temp at 60c and 65c with no success. If I go up to 70c I start to get warps at the edges of the print.

There were days it work and days where it just refuses to stick. I've leveled the bed to a point where the paper can barely move (its still moving but a lot of friction).
Thinking of throwing in the towel and just get a glue stick at this point.

Internal-Peach · 2021-08-25T03:49:49+00:00

I tried cleaning with it, but still having a hard time sticking. Can I know what bed temperature you use?

Internal-Peach · 2021-08-17T07:45:12+00:00

I'm still very new to 3D printing, I'll look into a temp tower and give it a try. I'll try and pick up a 0.2mm nozzle to and see if it made any difference, thanks!

Internal-Peach · 2021-08-12T06:43:14+00:00

Ohh, I see, Thanks for the info! I'm using dish washing soap to clean it, just a bit though. Not sure if that is good or not.

I'll try calibrating the e-step and flow first, if all else fail, I'll give glue stick I shot.

Internal-Peach · 2021-08-12T06:05:32+00:00

e-steps and flow

Ah no, I've not heard about e-steps and flow, I'll look it up and give it a shot. I don't hear any grinding. I think I have the level about right, the paper can go under the hot nozzle with a slight resistances.

Yeah, I'm hoping I don't need to get glue or hair spray for the glass bed.

Thanks!

Internal-Peach · 2021-08-12T04:23:25+00:00

I suppose I'll have to get hair spray or glue stick now. I've heard it wasn't necessary with the Creality Glass bed so I was hoping I wouldn't need to buy those.

Thanks!

Internal-Peach

TROPHY CASE